EN 13445-2:2014/A3:2018
(Amendment)Unfired pressure vessels - Part 2: Materials
Unfired pressure vessels - Part 2: Materials
This Part of this European Standard specifies the requirements for materials (including clad materials) for unfired pressure vessels and supports which are covered by EN 13445-1:2014 and manufactured from metallic materials; it is currently limited to steels with sufficient ductility but it is, for components operating in the creep range, also limited to sufficiently creep ductile materials .
It specifies the requirements for the selection, inspection, testing and marking of metallic materials for the fabrication of unfired pressure vessels.
Unbefeuerte Druckbehälter - Teil 2: Werkstoffe
Dieser Teil dieser Europäischen Norm legt die Anforderungen an Werkstoffe (einschließlich Plattierungswerkstoffe) für unbefeuerte Druckbehälter nach EN 13445-1:2014 aus metallischen Werkstoffen fest; die Norm ist zur Zeit auf Stähle mit ausreichender Duktilität begrenzt ; bei Bauteilen, die im Zeitstandbereich betrieben werden, ist sie jedoch außerdem auf Werkstoffe mit ausreichender Duktilität im Zeitstandbereich begrenzt.
Dieser Teil dieser Europäischen Norm legt die Anforderungen für die Auswahl, Inspektion, Prüfung und Kennzeichnung von metallischen Werkstoffen für die Herstellung von unbefeuerten Druckbehältern fest.
Récipients sous pression non soumis à la flamme - Partie 2 : matériaux
La présente partie de la Norme européenne spécifie les prescriptions relatives aux matériaux (y compris les matériaux plaqués) destinés aux récipients sous pression non soumis à la flamme et aux supports, couverts par l'EN 13445-1:2014, fabriqués à partir de matériaux métalliques ; elle est limitée actuellement aux aciers ayant une ductilité suffisante, mais elle est, dans le cas de composants en service dans le domaine du fluage, également limitée aux matériaux suffisamment ductiles au fluage.
Elle spécifie les prescriptions relatives à la sélection, l’inspection, les essais et le marquage des matériaux métalliques pour la fabrication des récipients sous pression non soumis à la flamme.
Neogrevane (nekurjene) tlačne posode - 2. del: Materiali - Dopolnilo A3
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13445-2:2014/A3:2018
01-november-2018
1HRJUHYDQH QHNXUMHQH WODþQHSRVRGHGHO 0DWHULDOL'RSROQLOR$
Unfired pressure vessels - Part 2: Materials
Unbefeuerte Druckbehälter - Teil 2: Werkstoffe
Récipients sous pression non soumis à la flamme - Partie 2 : matériaux
Ta slovenski standard je istoveten z: EN 13445-2:2014/A3:2018
ICS:
23.020.32 7ODþQHSRVRGH Pressure vessels
SIST EN 13445-2:2014/A3:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13445-2:2014/A3:2018
---------------------- Page: 2 ----------------------
SIST EN 13445-2:2014/A3:2018
EN 13445-2:2014/A3
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2018
EUROPÄISCHE NORM
ICS 23.020.30
English Version
Unfired pressure vessels - Part 2: Materials
Récipients sous pression non soumis à la flamme - Unbefeuerte Druckbehälter - Teil 2: Werkstoffe
Partie 2 : matériaux
This amendment A3 modifies the European Standard EN 13445-2:2014; it was approved by CEN on 13 May 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13445-2:2014/A3:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13445-2:2014/A3:2018
EN 13445-2:2014/A3:2018 (E)
Contents
Page
European foreword . 3
1 Modification to Clause 2 Normative reference . 4
2 Modifications to B.2.2.4 Bolts and nuts . 4
3 Modification to Table E.2-1 . 6
4 Modification to Annex F . 6
Annex F (normative) Special provisions for materials and components . 7
F.1 General . 7
F.2 Mechanical properties and technical delivery conditions for fasteners in accordance
with EN ISO 3506 . 7
F.2.1 Mechanical properties for austenitic bolts in accordance with EN ISO 3506-1 . 7
F.2.2 Delivery conditions for austenitic fasteners . 7
5 Modification to Annex Y . 8
2
---------------------- Page: 4 ----------------------
SIST EN 13445-2:2014/A3:2018
EN 13445-2:2014/A3:2018 (E)
European foreword
This document (EN 13445-2:2014/A3:2018) has been prepared by Technical Committee CEN/TC 54
“Unfired Pressure vessels”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2019, and conflicting national standards
shall be withdrawn at the latest by February 2019.
Attention is draw
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.