EN IEC 62196-2:2022

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility requirements for AC pin and contact-tube accessories

This part of IEC 62196 applies to EV plugs, EV socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories. These accessories have a nominal rated operating voltage not exceeding 480 V AC, 50 Hz to 60 Hz, and a rated current not exceeding 63 A three phase or 70 A single phase, for use in conductive charging of electric vehicles. This document covers the basic interface accessories for vehicle supply as specified in IEC 62196-1. NOTE 1 The term "Electric road vehicles (EV)" comprises all road vehicles, including plug-in hybrid road vehicles (PHEV) that derive all or part of their energy from the rechargeable energy storage systems (RESS). These accessories are intended to be used for circuits specified in IEC 61851-1:2017, which operate at different voltages and frequencies, and which can include extra-low voltage (ELV) and communication signals. The use of these accessories for bidirectional power transfer is under consideration. This document applies to accessories to be used in an ambient temperature between -30 °C and +40 °C. NOTE 2 In the following country, other requirements regarding the lower temperature may apply: NO. NOTE 3 In the following country, −35 °C applies: SE. These accessories are intended to be connected only to cables with copper or copper-alloy conductors. Vehicle inlets and vehicle connectors described in this document are intended to be used for charging in modes 1, 2 and 3, cases B and C. The EV socket-outlets and EV plugs covered by this document are intended to be used for charging mode 3 only, case A and B. The modes and permissible connections are specified in IEC 61851-1:2017.

Stecker, Steckdosen, Fahrzeugkupplungen und Fahrzeugstecker - Konduktives Laden von Elektrofahrzeugen - Teil 2: Maßliche Kompatibilitätsanforderungen an Wechselspannungssteckvorrichtungen mit Stiften und Buchsen

Fiches, socles de prise de courant, prises mobiles de véhicule et socles de connecteurs de véhicule - Charge conductive des véhicules électriques - Partie 2: Exigences dimensionnelles de compatibilité pour les appareils à broches et alvéoles pour courant alternatif

L’IEC 62196-2:2022 s’applique aux fiches VE, aux socles de prise de courant VE, aux prises mobiles et socles de connecteurs de véhicule, à broches et alvéoles, de configurations normalisées, ci-après dénommés appareils. Ces appareils ont une tension assignée d’emploi ne dépassant pas 480 V en courant alternatif, 50 Hz à 60 Hz, et un courant assigné ne dépassant pas 63 A en triphasé ou 70 A en monophasé, et sont destinés à la charge conductive des véhicules électriques. Le présent document couvre les appareils d’interface basique pour l’alimentation de véhicules tels que spécifiés dans l’IEC 62196-1:2022. Cette troisième édition annule et remplace la deuxième édition parue en 2016. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l’édition précédente:
les exigences d’interchangeabilité ont été supprimées du titre de la Partie 2;
alignement sur l’IEC 62196-1:2022 et l’IEC 62196-3:2022;
alignement sur l’IEC 61851-1:2017.

Vtiči, vtičnice, konektorji in uvodnice na vozilih - Kabelsko napajanje električnih vozil - 2. del: Zahteve za dimenzijsko skladnost za pribor s trni in cevastimi kontakti za izmenični tok (a.c.) (IEC 62196-2:2022)

Ta del standarda IEC 62196 se uporablja za vtiče, vtičnice, konektorje in uvodnice na električnih vozilih s trni in cevastimi kontakti standardiziranih oblik (v nadaljnjem besedilu: »priključki«). Njihova nominalna nazivna obratovalna napetost je manjša od 480 V izmenične napetosti, 50 Hz do 60 Hz, nazivni tok pa manjši od 63 A pri treh fazah ali 70 A pri eni fazi, za uporabo pri sistemih za polnjenje električnih vozil po kablu.
Ta dokument zajema osnovne vmesniške priključke za napajanje vozil, kot je opredeljeno v standardu IEC 62196-1.
OPOMBA 1: Izraz »električna cestna vozila (EV)« vključuje vsa cestna vozila, vključno s hibridnimi cestnimi vozili z možnostjo polnjenja prek navadne vtičnice (PHEV), ki vso energijo ali njen del pridobijo iz sistemov za shranjevanje energije z možnostjo ponovnega polnjenja (RESS) v vozilu.
Ti priključki so namenjeni za uporabo pri tokokrogih, navedenih v standardu IEC 61851-1:2017, ki delujejo pri različnih napetostih in frekvencah in lahko vključujejo malo napetost (ELV) in komunikacijske signale.
Uporaba teh priključkov za dvosmerni prenos moči je še v fazi preučevanja.
Ta dokument se uporablja za priključke za uporabo pri temperaturi okolja med –30 °C in +40 °C.
OPOMBA 2: V naslednji državi lahko veljajo druge zahteve glede nižje temperature: NO.
OPOMBA 3: V naslednji državi velja –35 °C: SE.
Ti priključki se lahko priključijo samo na kable z vodniki iz bakra ali bakrove zlitine.
Uvodnice in konektorji na vozilih, opisanih v tem dokumentu, se lahko uporabljajo pri polnjenju v načinu 1, 2 in 3, primera B in C. Vtičnice in vtiči za električna vozila iz tega dokumenta se lahko uporabljajo samo pri načinu polnjenja 3, primera A in B.
Načini in dovoljeni priključki so določeni v standardu IEC 61851-1:2017.

General Information

• Status: Published
• Publication Date: 24-Nov-2022
• ICS: 29.120.30 - Plugs, socket-outlets, couplers
• ICS: 43.120 - Electric road vehicles
• Technical Committee: CLC/TC 23H - Plugs, Socket-outlets and Couplers for industrial and similar applications, and for Electric Vehicles
• Drafting Committee: IEC/SC 23H - IEC_SC_23H
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 25-Nov-2022
• Completion Date: 25-Nov-2022
• Directive: 2014/35/EU - Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits
• Directive: 2014/94/EU - Directive 2014/94/EU of The European Parliament and of The Council of 22 October 2014 on the deployment of alternative fuels infrastructure
• Mandate: M/468 - Standardisation mandate addressed to CEN and CENELEC and ETSI concerning the charging of electric vehicles
• Mandate: M/511 - Mandate to CEN, CENELEC and ETSI relating to harmonised standards in the field of the Low Voltage Directive
• Mandate: M/533 - [C(2015)1330] Standardisation request addressed to CEN, CENELEC and ETSI in support of the implementation of the Directive 2014/94/EU on the deployment of alternative fuels infrastructure
• Ref Project: SIST EN IEC 62196-2:2023 - Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility requirements for AC pin and contact-tube accessories (IEC 62196-2:2022)

Relations

• Replaces: EN 62196-2:2017 - Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories
• Effective Date: 29-Nov-2022
• Revised: prEN IEC 62196-2:2024 - Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility requirements for AC pin and contact-tube accessories
• Effective Date: 04-Jul-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 62196-2:2023
01-maj-2023
Nadomešča:
SIST EN 62196-2:2017
Vtiči, vtičnice, konektorji in uvodnice na vozilih - Kabelsko napajanje električnih
vozil - 2. del: Zahteve za dimenzijsko skladnost za pribor s trni in cevastimi
kontakti za izmenični tok (a.c.) (IEC 62196-2:2022)
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of
electric vehicles - Part 2: Dimensional compatibility requirements for AC pin and contact-
tube accessories (IEC 62196-2:2022)
Stecker, Steckdosen, Fahrzeugkupplungen und Fahrzeugstecker - Konduktives Laden
von Elektrofahrzeugen - Teil 2: Maßliche Kompatibilitätsanforderungen an
Wechselspannungssteckvorrichtungen mit Stiften und Buchsen (IEC 62196-2:2022)
Fiches, socles de prise de courant, prises mobiles de véhicule et socles de connecteurs
de véhicule - Charge conductive des véhicules électriques - Partie 2: Exigences
dimensionnelles de compatibilité pour les appareils à broches et alvéoles pour courant
alternatif (IEC 62196-2:2022)
Ta slovenski standard je istoveten z: EN IEC 62196-2:2022
ICS:
29.120.30 Vtiči, vtičnice, spojke Plugs, socket-outlets,
couplers
43.120 Električna cestna vozila Electric road vehicles
SIST EN IEC 62196-2:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 62196-2:2023

---------------------- Page: 2 ----------------------
SIST EN IEC 62196-2:2023


EUROPEAN STANDARD EN IEC 62196-2

NORME EUROPÉENNE

EUROPÄISCHE NORM November 2022
ICS 29.120.30; 43.120 Supersedes EN 62196-2:2017
English Version
Plugs, socket-outlets, vehicle connectors and vehicle inlets -
Conductive charging of electric vehicles - Part 2: Dimensional
compatibility requirements for AC pin and contact-tube
accessories
(IEC 62196-2:2022)
Fiches, socles de prise de courant, prises mobiles de Stecker, Steckdosen, Fahrzeugkupplungen und
véhicule et socles de connecteurs de véhicule - Charge Fahrzeugstecker - Konduktives Laden von
conductive des véhicules électriques - Partie 2: Exigences Elektrofahrzeugen - Teil 2: Maßliche
dimensionnelles de compatibilité pour les appareils à Kompatibilitätsanforderungen an
broches et alvéoles pour courant alternatif Wechselspannungssteckvorrichtungen mit Stiften und
(IEC 62196-2:2022) Buchsen
(IEC 62196-2:2022)
This European Standard was approved by CENELEC on 2022-11-23. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 62196-2:2022 E

---------------------- Page: 3 ----------------------
SIST EN IEC 62196-2:2023
EN IEC 62196-2:2022 (E)
European foreword
The text of document 23H/502/FDIS, future edition 3 of IEC 62196-2, prepared by SC 23H "Plugs,
Socket-outlets and Couplers for industrial and similar applications, and for Electric Vehicles" of
IEC/TC 23 "Electrical accessories" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 62196-2:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-08-23
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-11-23
document have to be withdrawn
This document supersedes EN 62196-2:2017 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held re
...

SLOVENSKI STANDARD
oSIST prEN IEC 62196-2:2020
01-marec-2020
Vtiči, vtičnice, konektorji in uvodnice na vozilih - Kabelsko napajanje električnih
vozil - 2. del: Zahteve za dimenzijsko skladnost za pribor s trni in cevastimi
kontakti za izmenični tok (a.c.)
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of
electric vehicles - Part 2: Dimensional compatibility requirements for AC pin and contact-
tube accessories
Stecker, Steckdosen, Fahrzeugkupplungen und Fahrzeugstecker - Konduktives Laden
von Elektrofahrzeugen - Teil 2: Anforderungen und Hauptmaße für die Kompatibilität und
Austauschbarkeit von Stift- und Buchsensteckvorrichtungen für Wechselstrom
Fiches, socles de prise de courant, prises mobiles et socles de connecteurs de véhicules
- Charge conductive des véhicules électriques - Partie 2: Exigences dimensionnelles de
compatibilité et d'interchangeabilité pour les appareils à broches et alvéoles pour
courant alternatif
Ta slovenski standard je istoveten z: prEN IEC 62196-2:2020
ICS:
29.120.30 Vtiči, vtičnice, spojke Plugs, socket-outlets,
couplers
43.120 Električna cestna vozila Electric road vehicles
oSIST prEN IEC 62196-2:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN IEC 62196-2:2020

---------------------- Page: 2 ----------------------
oSIST prEN IEC 62196-2:2020
23H/463/CDV

COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 62196-2 ED3
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2020-01-10 2020-04-03
SUPERSEDES DOCUMENTS:
23H/445/CD,23H/450A/CC

IEC SC 23H : PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL AND SIMILAR APPLICATIONS, AND FOR ELECTRIC
VEHICLES
SECRETARIAT: SECRETARY:
France Mr Bertrand Doignon
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:

TC 64,TC 69
Other TC/SCs are requested to indicate their interest, if
any, in this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY

SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.

This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.

TITLE:
Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric
vehicles - Part 2: Dimensional compatibility requirements for AC pin and contact-tube
accessories

PROPOSED STABILITY DATE: 2025

Copyright © 2019 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to
download this electronic file, to make a copy and to print out the content for the sole purpose of preparing
National Committee positions. You may not copy or "mirror" the file or printed version of the document, or any
part of it, for any other purpose without permission in writing from IEC.

---------------------- Page: 3 ----------------------
oSIST prEN IEC 62196-2:2020
62196-2/Ed.3/CDV © IEC(E) 2 23H/463/CDV
NOTE FROM TC/SC OFFICERS:
If necessary, comments may be reviewed in an MT 8 meeting in April 2020

---------------------- Page: 4 ----------------------
oSIST prEN IEC 62196-2:2020
62196-2/Ed.3/CDV © IEC(E) 3 23H/463/CDV

1 CONTENTS
2
3 FOREWORD . 5
4 INTRODUCTION . 7
5 1 Scope . 8
6 2 Normative references . 8
7 3 Terms and definitions . 9
8 4 General . 9
9 5 Ratings . 9
10 6 Connection between the power supply and the electric vehicle . 9
11 6.201 Communication and control pilot function . 11
12 7 Classification of accessori
...