HD 129.4 S1:1977
(Main)Flanges for waveguides - Part 4: Relevant specifications for flanges for circular waveguides
Flanges for waveguides - Part 4: Relevant specifications for flanges for circular waveguides
Contains a detailed description of flanges for circular waveguides - Type J, including mechanical reqirements and electrical test, as well as tables and drawings.
Flansche für Hohlleiter - Teil 4: Allgemeine Empfehlungen für Flansche für Rundrohr-Hohlleiter
Brides pour guides d'ondes - Partie 4: Spécifications particulières de brides pour guides d'ondes circulaires
Contient une description détaillée des brides our guides d'ondes circulaires - type J, comprenant les prescriptions mécaniques, les essais électriques, ainsi que des dessins et tableaux.
Flanges for waveguides - Part 4: Specifications for flanges for circular waveguides
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST HD 129.4 S1:2002
prva izdaja
STANDARD
september 2002
Flanges for waveguides - Part 4: Specifications for flanges for circular waveguides
ICS 33.120.10 Referenčna številka
SIST HD 129.4 S1:2002(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
NORME CEI
INTERNATIONALE IEC
60154-4
INTERNATIONAL
Première édition
STAN
DARD
First edition
1969-01
Brides pour guides d'ondes
Quatrième partie:
Spécifications particulières
de brides
pour guides d'ondes circulaires
Flanges for waveguides
Part 4:
Relevant specifications for flanges
for circular waveguides
© IEC 1969 Droits de reproduction
réservés — Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in
utilisée sous quelque forme que ce soit et par
aucun any form or by any means, electronic or mechanical,
procédé, électronique ou mécanique, y compris la photo- including photocopying and microfilm, without permission in
copie et les microfilms, sans l'accord écrit de l'éditeur. writing from the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http: //www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale
PRICE CODE
International Electrotechnical Commission
IEC MemnyHaponriae 3netsrporexHwiecKaa
HoMHCCHA
Pour prix, voir catalogue en vigueur
•
For price, see current catalogue
---------------------- Page: 2 ----------------------
-3—
CONTENTS
Page
FOREWORD 5
PREFACE 5
General 9
Mechanical requirements 9
Type J flanges
Pressurizable 154 IEC — PJC 18 — PJC 28.7
Drawing - Figure 1 16
Tables la and Ib 21-24
Type J flanges
Pressurizable 154 IEC — PJC 30 — PJC 46.2
Drawing - Figure 2 17
Tables la and Ib 21-24
Type J flanges
Pressurizable 154 IEC — PJC 48 — PJC 73.9
Drawing - Figure 3 18
Tables la and Ib 21-24
Type J flanges
Pressurizable 154 IEC — PJC 76 — PJC 140
19
Drawing - Figure 4
Tables la and Ib 21-24
APPENDIX A — Notes for Table la (metric and inch) 13
APPENDIX B — Notes for Table Ib (metric and inch) 15
---------------------- Page: 3 ----------------------
-5—
INTERNATIONAL ELECTROTECHNICAL COMMISSION
FLANGES FOR WAVEGUIDES
Part 4: Relevant specifications for flanges
for circular waveguides
FOREWORD
1)The formal decisions or agreements of the IEC on technical matters, prepared by Technical Committees on which all the
National Committees having a special interest therein are represented, express, as nearly as possible, an international
consensus of opinion on the subjects dealt with.
2) They have the form of recommendations for international use and they are accepted by the National Committees in that
sense.
3) In order to promote this inte rnational unification, the IEC expresses the wish that all National Committees having as
yet no national rules, when preparing such rules, should use the IEC recommendations as the fundamental basis for these
rules in so far as national conditions will permit.
4) The desirability is recognized of extending inte rn
ational agreement on these matters through an endeavour to harmonize
national standardization rules with these recommendations in so far as national conditions will permit. The National
Committees pledge their influence towards that end.
5) The I E C has not laid down any procedure concerning marking as an indication of approval and has no responsibility
when an item of equipment is declared to comply with one of its recommendations.
PREFACE
This Recommendation has been prepared by Sub-Committee 46B, Waveguides and their Accessories,
of IEC Technical Committee No. 46, Cables, Wires and Waveguides for Telecommunication Equipment.
It forms the fourth pa of the complete Recommendation dealing with Flanges for Waveguides, and
rt
should be used in conjunction with Part 1, General Requirements and Measuring Methods, issued as
IEC Publication 154-1.
Subsequent relevant specifications for other types of flanges will be issued in separate publications.
A draft was discussed at the meeting held in Bucharest in 1962, as a result of which a new draft was
submitted to the National Committees for approval under the Six Months' Rule in January 1964. Comments
received were discussed at the meetings held in Baden-Baden in 1965 and in Tel-Aviv in 1966. Amend-
ments were submitted to the National Committees for approval under the Two Months' Procedure in
April 1967.
The following countries voted explicitly in favour of publication of Part 4:
Korea (Republic of)
Australia
Belgium South Africa
Czechoslovakia Sweden
Denmark Switzerland
Turkey
Finland
United Kingdom
France
United States of America
Germany
Yugoslavia
Israel
Italy Netherlands
Japan
---------------------- Page: 4 ----------------------
—7—
DIMENSIONAL DEV
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.