Petroleum and natural gas industries — General requirements for offshore structures

This document specifies general requirements and recommendations for the design and assessment of bottom-founded (fixed) and buoyant (floating) offshore structures. This document is applicable for all phases of the life of the structure, including: — successive stages of construction (i.e. fabrication, transportation, and installation), — service in-place, both during design life and during any life extensions, and — decommissioning, and removal. This document contains general requirements and recommendations for both the design of new build structures and for the structural integrity management and assessment of existing structures. This document does not apply to subsea and riser systems or pipeline systems.

Industries du pétrole et du gaz naturel — Exigences générales relatives aux structures en mer

Le présent document spécifie les exigences générales et recommandations régissant la conception et l'évaluation des structures en mer prenant appui sur le fond marin (fixes) et des structures en mer flottantes. Le présent document s'applique à toutes les phases du cycle de vie de la structure, y compris: — les étapes successives de construction (c'est-à-dire la fabrication, le transport et l'installation); — l'exploitation, à la fois pendant la durée de vie de conception et pendant toute prolongation de la durée de vie; et — l'abandon et l'enlèvement. Le présent document contient des exigences générales et recommandations à la fois pour la conception de nouvelles structures et pour la gestion et l'évaluation de l'intégrité structurelle des structures existantes. Le présent document ne s'applique pas aux systèmes sous-marins de tubes conducteurs ou de conduites.

General Information

Status

Published

Publication Date

13-Jun-2019

ICS

75.180.10 - Exploratory, drilling and extraction equipment

Technical Committee

ISO/TC 67/SC 7 - Offshore structures

Drafting Committee

ISO/TC 67/SC 7/WG 1 - General requirements

Current Stage

9020 - International Standard under periodical review

Start Date

15-Apr-2024

Completion Date

15-Apr-2024

Ref Project

Relations

Revises

ISO 19900:2013 - Petroleum and natural gas industries — General requirements for offshore structures

Effective Date

05-Nov-2015

Buy Standard

ISO 19900:2019 - Petroleum and natural gas industries -- General requirements for offshore structures

Standard

ISO 19900:2019 - Petroleum and natural gas industries -- General requirements for offshore structures

English language

64 pages

sale 15% off

Preview

sale 15% off

Preview

ISO 19900:2019 - Industries du pétrole et du gaz naturel -- Exigences générales relatives aux structures en mer

Standard

ISO 19900:2019 - Industries du pétrole et du gaz naturel -- Exigences générales relatives aux structures en mer

French language

70 pages

sale 15% off

Preview

sale 15% off

Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 19900
Third edition
2019-06
Petroleum and natural gas
industries — General requirements
for offshore structures
Industries du pétrole et du gaz naturel — Exigences générales
relatives aux structures en mer
Reference number
ISO 19900:2019(E)
©
ISO 2019

---------------------- Page: 1 ----------------------
ISO 19900:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 19900:2019(E)

Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Symbols and abbreviated terms . 8
4.1 Symbols . 8
4.2 Abbreviated terms . 9
5 Fundamental requirements . 9
5.1 General . 9
5.2 Structural integrity requirements .10
5.3 Functional requirements .10
5.4 Requirements for specific phases of the life of the structure .11
5.4.1 Planning .11
5.4.2 Construction and deployment .11
5.4.3 Structural integrity management .11
5.4.4 Decommissioning and removal .11
5.5 Requirements for durability and robustness .12
5.5.1 Durability, maintenance and inspection .12
5.5.2 Robustness .12
6 Basis f
...

NORME ISO
INTERNATIONALE 19900
Troisième édition
2019-06
Industries du pétrole et du gaz
naturel — Exigences générales
relatives aux structures en mer
Petroleum and natural gas industries — General requirements for
offshore structures
Numéro de référence
ISO 19900:2019(F)
©
ISO 2019

---------------------- Page: 1 ----------------------
ISO 19900:2019(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2019
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2019 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 19900:2019(F)

Sommaire Page
Avant-propos .vi
Introduction .vii
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 2
4 Symboles et termes abrégés . 9
4.1 Symboles . 9
4.2 Termes abrégés .10
5 Exigences fondamentales .10
5.1 Généralités .10
5.2 Exigences relatives à l'intégrité structurelle .10
5.3 Exigences fonctionnelles .11
5.4 Exigences relatives à des phases spécifiques de la vie de la structure .11
5.4.1 Planification .11
5.4.2 Construction et déploiement .12
5.4.3 Gestion de l'intégrité structurelle. .12
5.4.4 Abandon et enlèvement .12
5.5 Exigences relatives à la pérennité et à la robustesse .12
5.5.1 Pérennité, maintenance et inspection .12
5.5.2 Robustesse .13
6 Base de co
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO

ISO 19901-3:2024(Main)

Oil and gas industries including lower carbon energy — Specific requirements for offshore structures — Part 3: Topsides structure

This document provides requirements, guidance and information for the design and fabrication of topsides structure for offshore structures, including in-service, pre-service and post-service conditions. The actions on topsides structure and the action effects in structural components are derived from this document, where necessary in combination with other International Standards in the ISO 19901 series (e.g. ISO 19901-1 for wind actions - see 7.6.2, ISO 19901-2 for seismic actions - see 7.7) and ISO 19902 for fatigue design (see 6.7). This document is applicable to the following: — topsides of fixed offshore structures; — discrete structural units placed on the hull structures of floating offshore structures and mobile offshore units; — topsides of arctic offshore structures, excluding winterization (see ISO 19906). If any part of the topsides structure forms part of the primary structure of the overall structural system which resists global platform actions, the requirements of this document are supplemented with applicable requirements in ISO 19902, ISO 19903, ISO 19904-1, ISO 19905-1, ISO 19905-3 and ISO 19906. For those parts of floating offshore structures and mobile offshore units that are chosen to be governed by the rules of a recognized classification society, the corresponding class rules supersede the associated requirements of this document. This document also addresses prevention, control and assessment of fire, explosions and other accidental events. The fire and explosion provisions of this document can be applied to those parts of the hulls of floating structures and mobile offshore units that contain hydrocarbon processing, piping or storage. NOTE Requirements for structural integrity management are presented in ISO 19901-9. This document applies to structural components including the following: — primary and secondary structure in decks, module support frames and modules; — flare structures; — crane pedestal and other crane support arrangements; — helicopter landing decks (helidecks); — permanent bridges between separate offshore structures; — masts, towers and booms on offshore structures. This document provides requirements for selecting and using a national building standard with a correspondence factor for determining the resistance of rolled and welded non-circular prismatic components and their connections.

Standard
151 pages
English language
sale 15% off
Standard
158 pages
French language
sale 15% off

ISO

ISO 19905-1:2023(Main)

Oil and gas industries including lower carbon energy — Site-specific assessment of mobile offshore units — Part 1: Jack-ups: elevated at a site

This document specifies requirements and provides recommendation and guidance for the elevated site-specific assessment (SSA-E) of independent leg jack‑up units for use in the petroleum and natural gas industries. It addresses: a) occupied non-evacuated, occupied evacuated and unoccupied jack‑ups; b) the installed (or elevated) phase at a specific site. It also addresses the requirement that the as-installed condition matches the assumptions used in the assessment. This document does not address the site-specific assessment of installation and removal (SSA-I). To ensure acceptable reliability, the provisions of this document form an integrated approach, which is used in its entirety for the site-specific assessment of a jack‑up. When assessing a jack-up operating in regions subject to sea ice and icebergs, it is intended that the assessor supplements the provisions of this document with the relevant provisions relating to ice actions contained in ISO 19906 and procedures for ice management contained in ISO 35104. This document does not address design, transit to and from site, or installation and removal from site. This document is applicable only to independent leg mobile jack-up units that are structurally sound and adequately maintained, which is normally demonstrated through holding a valid recognized classification society, classification certificate. Jack‑ups that do not hold a valid recognized classification society certificate are assessed according to the provisions of ISO 19902, supplemented by methodologies from this document, where applicable. NOTE 1 Well conductors can be a safety-critical element for jack‑up operations. However, the integrity of well conductors is not part of the site-specific assessment process for jack‑ups and is, therefore, not addressed in this document. See A.1 for guidance on this topic. NOTE 2 RCS rules and the IMO MODU code (International Maritime Organisation Mobile Offshore Drilling Unit code) provide guidance for the design of jack-ups.

Standard
369 pages
English language
sale 15% off
Standard
387 pages
French language
sale 15% off

ISO

ISO 19901-8:2023(Main)

Oil and gas industries including lower carbon energy — Offshore structures — Part 8: Marine soil investigations

This document specifies requirements and provides recommendations and guidelines for marine soil investigations regarding: a) objectives, planning and execution of marine soil investigations; b) deployment of investigation equipment; c) drilling and logging; d) in situ testing; e) sampling; f) laboratory testing; g) reporting. Although this document focuses on investigations of soil, it also provides guidance, with less detail, for investigations of chalk, calcareous soils, cemented soils and weak rock. Foundation design is not covered by this document. NOTE 1 ISO 19901‑4 and the respective design standards covering foundation design for the specific types of offshore structures to meet the requirements of application specific standards are given on the ISO website. The results from marine geophysical investigations are, when available and where appropriate, used for planning, optimization and interpretation of marine soil investigations. This document neither covers the planning, execution and interpretation of marine geophysical investigations nor the planning and scope of geohazard assessment studies, only the corresponding marine soil investigations aspects thereof. NOTE 2 ISO 19901-10 covers the planning, execution and interpretation of marine geophysical investigations. This document specifies requirements and provides guidance for obtaining measured values and derived values. This document excludes requirements for determination of design values and representative values. Limited guidance is provided in 11.3 related to data interpretation. This document is intended for clients, soil investigation contractors, designers, installation contractors, geotechnical laboratories and public and regulatory authorities concerned with marine soil investigations for any type of offshore structures, or geohazard assessment studies.

Standard
154 pages
English language
sale 15% off
Standard
161 pages
French language
sale 15% off

ISO

ISO 19901-2:2022(Main)

Petroleum and natural gas industries — Specific requirements for offshore structures — Part 2: Seismic design procedures and criteria

This document contains requirements for defining the seismic design procedures and criteria for offshore structures; guidance on the requirements is included in Annex A. The requirements focus on fixed steel offshore structures and fixed concrete offshore structures. The effects of seismic events on floating structures and partially buoyant structures are briefly discussed. The site-specific assessment of jack-ups in elevated condition is only covered in this document to the extent that the requirements are applicable. Only earthquake-induced ground motions are addressed in detail. Other geologically induced hazards such as liquefaction, slope instability, faults, tsunamis, mud volcanoes and shock waves are mentioned and briefly discussed. The requirements are intended to reduce risks to persons, the environment, and assets to the lowest levels that are reasonably practicable. This intent is achieved by using: a) seismic design procedures which are dependent on the exposure level of the offshore structure and the expected intensity of seismic events; b) a two-level seismic design check in which the structure is designed to the ultimate limit state (ULS) for strength and stiffness and then checked to abnormal environmental events or the abnormal limit state (ALS) to ensure that it meets reserve strength and energy dissipation requirements. Procedures and requirements for a site-specific probabilistic seismic hazard analysis (PSHA) are addressed for offshore structures in high seismic areas and/or with high exposure levels. However, a thorough explanation of PSHA procedures is not included. Where a simplified design approach is allowed, worldwide offshore maps, which are included in Annex B, show the intensity of ground shaking corresponding to a return period of 1 000 years. In such cases, these maps can be used with corresponding scale factors to determine appropriate seismic actions for the design of a structure, unless more detailed information is available from local code or site-specific study. NOTE For design of fixed steel offshore structures, further specific requirements and recommended values of design parameters (e.g. partial action and resistance factors) are included in ISO 19902, while those for fixed concrete offshore structures are contained in ISO 19903. Seismic requirements for floating structures are contained in ISO 19904, for site-specific assessment of jack-ups and other MOUs in the ISO 19905 series, for arctic structures in ISO 19906 and for topsides structures in ISO 19901‑3.

Standard
55 pages
English language
sale 15% off
Standard
59 pages
French language
sale 15% off

ISO

ISO 19901-5:2021(Main)

Petroleum and natural gas industries — Specific requirements for offshore structures — Part 5: Weight management

This document specifies requirements for managing and controlling the weight and centre of gravity (CoG) of offshore facilities by means of mass management during all lifecycle phases including; conceptual design, front end engineering design (FEED), detail engineering, construction and operations. These can be new facilities (greenfield) or modifications to existing facilities (brownfield). Weight management is necessary throughout operations, decommissioning and removal to facilitate structural integrity management (SIM). The provisions of this document are applicable to fixed and floating facilities of all types. Weight management only includes items with static mass. Snow and ice loads are excluded as they are not considered to be part of the facility. Dynamic loads are addressed in ISO 19904-1, ISO 19901-6 and ISO 19901-7. This document specifies: a) requirements for managing and controlling weights and CoGs of assemblies and entire facilities; b) requirements for managing weight and CoG interfaces; c) standardized terminology for weight and CoG estimating and reporting; d) requirements for determining not-to-exceed (NTE) weights and budget weights; e) requirements for weighing and determination of weight and centre of gravity (CoG) of tagged equipment, assemblies, modules and facilities; This document can be used: f) as a basis for costing, scheduling or determining suitable construction method(s) or location(s) and installation strategy; g) as a basis for planning, evaluating and preparing a weight management plan and reporting system; h) as a contract reference; i) as a means of refining the structural analysis or model.

Standard
65 pages
English language
sale 15% off
Standard
71 pages
French language
sale 15% off
Standard
71 pages
French language
sale 15% off

ISO

ISO 19901-10:2021(Main)

Petroleum and natural gas industries — Specific requirements for offshore structures — Part 10: Marine geophysical investigations

This document provides requirements and guidelines for marine geophysical investigations. It is applicable to operators/end users, contractors and public and regulatory authorities concerned with marine site investigations for offshore structures for petroleum and natural gas industries. This document provides requirements, specifications, and guidance for: a) objectives, planning, and quality management; b) positioning; c) seafloor mapping, including instrumentation and acquisition parameters, acquisition methods, and deliverables; d) sub-seafloor mapping, including seismic instrumentation and acquisition parameters, and non-seismic-reflection methods; e) reporting; f) data integration, interpretation, and investigation of geohazards. This document is applicable to investigation of the seafloor and the sub-seafloor, from shallow coastal waters to water depths of 3 000 m and more. It provides guidance for the integration of the results from marine soil investigations and marine geophysical investigations with other relevant datasets. NOTE 1 The depth of interest for sub-seafloor mapping depends on the objectives of the investigation. For offshore construction, the depths of investigation are typically in the range 1 m below seafloor to 200 m below seafloor. Some methods for sub-seafloor mapping can also achieve much greater investigation depths, for example for assessing geohazards for hydrocarbon well drilling. There is a fundamental difference between seafloor mapping and sub-seafloor mapping: seafloor signal resolution can be specified, while sub-seafloor signal resolution and penetration cannot. This document therefore contains requirements for the use of certain techniques for certain types of seafloor mapping and sub-seafloor mapping (similarly, requirements are given for certain aspects of data processing). If other techniques can be shown to obtain the same information, with the same or better resolution and accuracy, then those techniques may be used. Mapping of pre-drilling well-site geohazards beneath the seafloor is part of the scope of this document. NOTE 2 This implies depths of investigation that are typically 200 m below the first pressure-containment casing string or 1 000 m below the seafloor, whichever is greatest. Mapping of pre-drilling well-site geohazards is therefore the deepest type of investigation covered by this document. In this document, positioning information relates only to the positioning of survey platforms, sources and receivers. The processes used to determine positions of seafloor and sub-seafloor data points are not covered in this document. Guidance only is given in this document for the use of marine shear waves (A.8.3.3), marine surface waves (A.8.3.4), electrical resistivity imaging (A.8.3.5) and electromagnetic imaging (A.8.3.6).

Standard
81 pages
English language
sale 15% off
Standard
86 pages
French language
sale 15% off
Standard
86 pages
French language
sale 15% off

ISO

ISO 19905-3:2021(Main)

Petroleum and natural gas industries — Site-specific assessment of mobile offshore units — Part 3: Floating units

This document specifies requirements and recommendations for the site-specific assessment of mobile floating units for use in the petroleum and natural gas industries. It addresses the installed phase, at a specific site, of manned non-evacuated, manned evacuated and unmanned mobile floating units. This document addresses mobile floating units that are monohull (e.g. ship-shaped vessels or barges); column-stabilized, commonly referred to as semi-submersibles; or other hull forms (e.g. cylindrical/conical shaped). It is not applicable to tension leg platforms. Stationkeeping can be provided by a mooring system, a thruster assisted mooring system, or dynamic positioning. The function of the unit can be broad, including drilling, floatel, tender assist, etc. In situations where hydrocarbons are being produced, there can be additional requirements. This document does not address all site considerations, and certain specific locations can require additional assessment. This document is applicable only to mobile floating units that are structurally sound and adequately maintained, which is normally demonstrated through holding a valid RCS classification certificate. This document does not address design, transportation to and from site, or installation and removal from site. This document sets out the requirements for site-specific assessments, but generally relies on other documents to supply the details of how the assessments are to be undertaken. In general: — ISO 19901‑7 is referenced for the assessment of the stationkeeping system; — ISO 19904‑1 is referenced to determine the effects of the metocean actions on the unit; — ISO 19906 is referenced for arctic and cold regions; — the hull structure and air gap are assessed by use of a comparison between the site-specific metocean conditions and its design conditions, as set out in the RCS approved operations manual; — ISO 13624‑1 and ISO/TR 13624‑2[1] are referenced for the assessment of the marine drilling riser of mobile floating drilling units. Equivalent alternative methodologies can be used; — IMCA M 220 is referenced for developing an activity specific operating guidelines. Agreed alternative methodologies can be used. NOTE RCS rules and the IMO MODU code[13] provide guidance for design and general operation of mobile floating units.

Standard
22 pages
English language
sale 15% off
Standard
25 pages
French language
sale 15% off

ISO

ISO 19902:2020(Main)

Petroleum and natural gas industries — Fixed steel offshore structures

This document specifies requirements and provides recommendations applicable to the following types of fixed steel offshore structures for the petroleum and natural gas industries: ? caissons, free-standing and braced; ? jackets; ? monotowers; ? towers. In addition, it is applicable to compliant bottom founded structures, steel gravity structures, jack-ups, other bottom founded structures and other structures related to offshore structures (such as underwater oil storage tanks, bridges and connecting structures). This document contains requirements for planning and engineering of the design, fabrication, transportation and installation of new structures as well as, if relevant, their future removal. NOTE 1 Specific requirements for the design of fixed steel offshore structures in arctic environments are presented in ISO 19906. NOTE 2 Requirements for topsides structures are presented in ISO 19901-3; for marine operations in, ISO 19901‑6; for structural integrity management, in ISO 19901-9 and for the site-specific assessment of jack-ups, in ISO 19905‑1.

Standard
565 pages
English language
sale 15% off

ISO

ISO 19903:2019(Main)

Petroleum and natural gas industries — Concrete offshore structures

This document specifies requirements and provides recommendations applicable to fixed, floating and grounded concrete offshore structures for the petroleum and natural gas industries and for structures supporting nationally-important power generation, transmission or distribution facility. This document specifically addresses — the design, construction, transportation and installation of new structures, including requirements for in-service inspection and possible removal of structures, — the assessment of structures in service, and — the assessment of structures for reuse at other locations. This document is intended to cover the engineering processes needed for the major engineering disciplines to establish a facility for offshore operation.

Standard
115 pages
English language
sale 15% off
Standard
128 pages
French language
sale 15% off
Standard
128 pages
French language
sale 15% off

ISO

ISO 19901-9:2019(Main)

Petroleum and natural gas industries — Specific requirements for offshore structures — Part 9: Structural integrity management

This document specifies principles for the structural integrity management (SIM) of offshore structures subjected to known or foreseeable types of actions. This document specifies requirements and provides recommendations applicable to the following types of fixed steel offshore structures for the petroleum and natural gas industries: — caissons, free-standing and braced; — jackets; — monotowers; — towers. This document is applicable to topsides, including but not limited to the main decks, deck legs, topsides modules, crane pedestals, helideck, drilling derrick, skid beams, flare booms, exhaust towers, radio tower, conductor support frames, and lifeboat davits. In addition, it is applicable to compliant bottom founded structures, steel gravity structures, jack-ups, other bottom founded structures and other structures related to offshore structures (e.g. underwater oil storage tanks, bridges and connecting structures), to the extent to which its requirements are relevant. This document contains requirements for planning and engineering of the following tasks: a) integrity management data requirements; b) in-service inspection and integrity management of both new and existing structures; c) assessment of existing structures; d) evaluation of structures for reuse at different locations; e) evaluation of structures for their future removal.

Standard
143 pages
English language
sale 15% off
Standard
158 pages
French language
sale 15% off