ISO 5600:2017

Rubber — Determination of adhesion to rigid materials using conical shaped parts

ISO 5600:2017 specifies a method for the determination of the static vulcanized adhesion strength of rubber compounds to rigid materials. The test piece is composed of two conical ends of the rigid material, joined by a cylinder of rubber. The adhesion is obtained by a bonding system which can include not only the rigid material and the rubber compound, but other elements such as thin alloy coatings or chemical treatments of rigid parts and either a single cement or both primer and cover cements. The bonding system for preparing the test pieces should be adequately specified by the user, but provision is made in this document for the evaluation of different types of failure related to a complex bonding system. The method is designed primarily for test pieces prepared in the laboratory under standard conditions in order to provide data for development and control of bonding systems and their components, such as cements or special rubber compounds, and of methods of manufacture. While intended to be applied where the rubber is bonded to rigid supporting pieces, it might not cover such cases where the support, although of high-modulus material, has a low rigidity due to small transverse dimensions, as in the case of rubber bonded to metal wires, cords or thin sheets.

Caoutchouc — Détermination de l'adhérence aux matériaux rigides au moyen de pièces coniques

General Information

• Status: Withdrawn
• Publication Date: 31-May-2017
• ICS: 83.060 - Rubber
• Technical Committee: ISO/TC 45/SC 2 - Testing and analysis
• Drafting Committee: ISO/TC 45/SC 2/WG 1 - Physical properties
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 22-Apr-2024

Relations

• Consolidated By: ISO 17294-1:2024 - Water quality — Application of inductively coupled plasma mass spectrometry (ICP-MS) — Part 1: General requirements
• Effective Date: 06-Jun-2022
• Revised: ISO 5600:2024 - Rubber — Determination of adhesion to rigid materials using conical shaped parts
• Effective Date: 06-May-2023
• Revises: ISO 5600:2011 - Rubber — Determination of adhesion to rigid materials using conical shaped parts
• Effective Date: 10-Dec-2016

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 5600
Fifth edition
2017-06
Rubber — Determination of adhesion
to rigid materials using conical
shaped parts
Caoutchouc — Détermination de l’adhérence aux matériaux rigides
au moyen de pièces coniques
Reference number
ISO 5600:2017(E)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 5600:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 5600:2017(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Calibration . 2
7 Test piece . 2
7.1 Form and dimensions . . 2
7.2 Materials . 2
7.3 Preparation . 3
7.4 Number of test pieces . 3
7.5 Conditioning of test pieces . 3
8 Procedure. 4
9 Expression of results . 4
9.1 Adhesion value . 4
9.2 Type of adhesion failure . 4
10 Salvaging of bonded metal parts . 4
11 Test report .
...