Intelligent transport systems — Framework for collaborative Telematics Applications for Regulated commercial freight Vehicles (TARV) — Part 2: Common platform parameters using CALM

ISO 15638-2:2013 defines a generic cooperative ITS service platform for TARV using CALM, including protocol of coding, timing, and performance and support interfaces (such as driver ID card/USB or similar etc.).

Systèmes intelligents de transport — Cadre pour applications télématiques collaboratives pour véhicules de fret commercial réglementé (TARV) — Partie 2: Paramètres de plate-forme commune utilisant CALM

General Information

Status

Published

Publication Date

02-Jun-2013

ICS

03.220.20 - Road transport

35.240.60 - IT applications in transport

Technical Committee

ISO/TC 204 - Intelligent transport systems

Drafting Committee

ISO/TC 204/WG 7 - General fleet management and commercial/freight

Current Stage

9060 - Close of review

Start Date

04-Mar-2029

Ref Project

Relations

Consolidated By

ISO 14118:2017 - Safety of machinery — Prevention of unexpected start-up

Effective Date

06-Jun-2022

Buy Standard

ISO 15638-2:2013 - Intelligent transport systems -- Framework for collaborative Telematics Applications for Regulated commercial freight Vehicles (TARV)

Standard

ISO 15638-2:2013 - Intelligent transport systems -- Framework for collaborative Telematics Applications for Regulated commercial freight Vehicles (TARV)

English language

65 pages

sale 15% off

Preview

sale 15% off

Preview

Standards Content (Sample)

ISO 15638-2:2013 - Intelligent...

INTERNATIONAL ISO
STANDARD 15638-2
First edition
2013-06-15

Intelligent transport systems —
Framework for collaborative Telematics
Applications for Regulated commercial
freight Vehicles (TARV) —
Part 2:
Common platform parameters using
CALM
Systèmes intelligents de transport — Cadre pour applications
télématiques collaboratives pour véhicules de fret commercial
réglementé (TARV) —
Partie 2: Paramètres de plate-forme commune utilisant CALM

Reference number
ISO 15638-2:2013(E)
©
ISO 2013

---------------------- Page: 1 ----------------------
ISO 15638-2:2013(E)

COPYRIGHT PROTECTED DOCUMENT

© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any
means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission.
Permission can be requested from either ISO at the address below or ISO’s member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2013 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 15638-2:2013(E)
Contents Page
Foreword . v
Introduction . vii
1 Scope . 1
2 Conformance . 1
3 Normative references . 1
4 Terms and definitions . 3
5 Symbols (and abbreviated terms) . 4
6 General overview and framework . 8
7. Requirements . 10
7.1 General . 10
7.2 ISO 21217 CALM Architecture . 10
7.2.1 ISO 21217 General requirement . 10
7.2.2 ISO 21217 Specific aspects as they relate to TARV . 11
7.2.3 ISO 21217 Communication interface and channel types . 11
7.2.4 ISO 21217 Handover . 12
7.2.5 ISO 21217 IVS - ITS subsystem . 12
7.2.6 ISO 21217 Roadside ITS subsystem . 13
7.2.7 ISO 21217 Communication scenarios and classes . 14
7.3 ISO 21217 ITS-station reference architecture . 17
7.4 ISO 21217 Host, router, and gateway architecture . 19
7.5 ISO 21217 Service . 19
7.5.1 ISO 21217 ITS service . 19
7.5.2 ISO 21217 ITS-station service . 19
7.5.3 ISO 21217 Details related to the access layer . 19
7.5.4 ISO 21217 Details related to the networking and transport layer .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO

ISO/TS 23374-2:2023(Main)

Intelligent transport systems — Automated valet parking systems (AVPS) — Part 2: Security integration for type 3 AVP

This document specifies security means and procedures for AVPS Type 3 as specified in ISO 23374-1. It focuses on operation interfaces and management interfaces as defined in ISO 23374-1.

Technical specification
44 pages
English language
sale 15% off
Draft
44 pages
English language
sale 15% off
Draft
44 pages
English language
sale 15% off

ISO

ISO 17573-3:2023(Main)

Electronic fee collection — System architecture for vehicle-related tolling — Part 3: Data dictionary

This document specifies the syntax and semantics of data objects in the field of electronic fee collection (EFC). The definitions of data types and assignment of semantics are provided in accordance with the abstract syntax notation one (ASN.1) technique, as specified in ISO/IEC 8824-1. This document defines: — ASN.1 (data) types within the fields of EFC; — ASN.1 (data) types of a more general use that are used more specifically in standards related to EFC. This document does not seek to define ASN.1 (data) types that are primarily related to other fields that operate in conjunction with EFC, such as cooperative intelligent transport systems (C-ITS), the financial sector, etc.

Standard
49 pages
English language
sale 15% off

ISO

ISO 23374-1:2023(Main)

Intelligent transport systems — Automated valet parking systems (AVPS) — Part 1: System framework, requirements for automated driving and for communications interface

Automated valet parking systems (AVPSs) perform level 4 automated driving of individual or multiple unoccupied vehicles within a prescribed area of a parking facility. This document specifies performance requirements for the operation functions, the environmental conditions within parking facilities where automated vehicle operation is performed, and the test procedures to verify the performance requirements. An AVPS is comprised of physically separated sub-systems distributed among vehicles, facility equipment and user domains. The functionalities of AVPSs are realized by cooperation of these sub-systems, which are, in many cases, provided by different organizations. This document defines the system architecture and the communication interfaces between the sub-systems at the logical level. An AVPS manages its system participants (i.e. AVPS-compliant vehicles and parking facilities) and provides interfaces to other facility users and involved persons (e.g. system operators, facility managers). This document contains requirements for the management functions such as checking compatibility between vehicles and parking facilities, performing remote assistance and recovery when automated driving cannot be performed, and executing operation stop commands in response to the actions of other facility users. AVPSs are intended for use by a service provider upon receiving authority over vehicles from individual service recipients. This document does not include parking automation technologies that are solely based on usage by an individual user. If the vehicle is put into driverless operation directly by the user, this is not considered to be part of the AVPS.

Standard
153 pages
English language
sale 15% off

ISO

ISO/TS 22726-1:2023(Main)

Intelligent transport systems — Dynamic data and map database specification for connected and automated driving system applications — Part 1: Architecture and logical data model for harmonization of static map data

Technical specification
146 pages
English language
sale 15% off
Draft
146 pages
English language
sale 15% off
Draft
146 pages
English language
sale 15% off

ISO

ISO/TS 37444:2023(Main)

Electronic fee collection — Charging performance framework

This document defines the charging performance metrics to be used during the evaluation or on-going monitoring of an electronic fee collection (EFC) system and the examination framework for the measurement of these metrics. It specifies a method for the specification and documentation of a specific examination framework which can be used by the responsible entity to evaluate charging performance for a particular information exchange interface or for overall charging performance within a toll scheme. The following scheme types are within the scope of this document: a) discrete schemes; b) continuous schemes (autonomous type of systems). This document defines measurements only on standardized interfaces. This document defines metrics for the charging performance of EFC systems in terms of the level of errors associated with charging computation. This document describes a set of metrics with definitions, principles and formulations, which together make up a reference framework for the establishment of requirements for EFC systems and the subsequent examination of charging performance. This document defines metrics for the following information exchanges: — charge reports (including usage evidence); — toll declarations; — exception lists; — billing details and associated event data; — payment claims on the level of service user accounts; — end-to-end metrics which assess the overall performance of the charging process. These metrics focus solely on the outcome of the charging process, i.e. the amount charged in relation to a pre-measured or theoretically correct amount, rather than intermediate variables from various components as sensors, such as positioning accuracy, signal range or optical resolution. This approach ensures comparable results for each metric in all relevant situations. The following aspects are outside the scope of this document. — Definition of specific numeric performance bounds, or average or worst-case error bounds in percentage or monetary units. — Specification of a common reference system which would be required for comparison of performance between systems. — Measurements on proprietary interfaces. NOTE It is not possible to define standardized metrics on such system properties. Neither is it possible to define metrics for parts of the charging processing chain which are considered to be the internal matter of an interoperability partner, such as: — equipment performance, e.g. for on-board equipment (OBE), roadside equipment (RSE) or data centres such as signal range, optical resolution or computing system availability; — position performance metrics: the quality of data generated by position sensors is considered as an internal aspect of the GNSS front end. It is masked by correction algorithms, filtering, inferring of data and the robustness of the charge object recognition algorithms. — The evaluation of the expected performance of a system based on modelling and measured data from a trial at another place.

Technical specification
118 pages
English language
sale 15% off
Draft
120 pages
English language
sale 15% off
Draft
120 pages
English language
sale 15% off

ISO

ISO/TS 23792-1:2023(Main)

Intelligent transport systems — Motorway chauffeur systems (MCS) — Part 1: Framework and general requirements

Motorway chauffeur systems (MCS) perform Level 3 automated driving on limited access motorways with the presence of a fallback-ready user (FRU). MCS can be implemented in various forms capable of responding to different driving scenarios. This document describes a framework of MCS including system characteristics, system states/transition conditions and system functions. MCS are equipped with a basic set of functionalities to perform in-lane operation and can also be equipped with additional functionalities such as lane changing. This document specifies requirements of the basic set of functionalities and test procedures to verify these requirements. The requirements include vehicle operation to perform the entire dynamic driving task (DDT) within the current lane of travel, to issue a request to intervene (RTI) before disengaging, and to extend operation and temporarily continue to perform the DDT after issuing an RTI. This document describes one specific form of system engagement. Other forms are possible. These other system engagement forms, especially those provided in combination with other driving automation system features, are not within the scope of this document. Requirements and test procedures for the additional functionalities are provided in other parts of the ISO 23792 series. Means related to setting a destination and selecting a route to reach the destination are not within the scope of this document. This document applies to MCS installed in light vehicles.

Technical specification
30 pages
English language
sale 15% off
Draft
30 pages
English language
sale 15% off
Draft
30 pages
English language
sale 15% off

ISO

ISO 21219-17:2023(Main)

Intelligent transport systems — Traffic and travel information via transport protocol experts group, generation 2 (TPEG2) — Part 17: Speed information (TPEG2-SPI)

This document defines the TPEG Speed information (SPI) application for reporting speed information for travellers. Speed limits are usually indicated to the driver through roadside signs. Drivers who are aware of the speed limit at all times are more likely to drive safely, which improves road safety. Most speed limit signs are static and remain unchanged for years and are thus available through navigation system map databases. However, there is an increasing number of variable message signs, temporary signing (e.g. for road works) and also changed speed limits which are not yet reflected in the map databases. With the TPEG-SPI application, speed limit information is offered in an accurate way so that different lanes and different vehicle types can be differentiated. TPEG-SPI also allows the drivers to be aware of the current allowed (maximum) speed, by delivering timely information about the current position and values of speed limits to the navigation or driver assistance systems. These data are seen as informational and are intended to be encoded in a compact way to minimize bandwidth consumption. TPEG2-SPI supports direct and indirect speed limits. Direct speed limits are used for signs showing a maximum speed at which a vehicle is allowed to travel. Such speed limit signs can be static or dynamic. Indirect speed limits refer to the speed of other road users. It is primarily the vehicle in front of the own vehicle that is used as a reference.

Standard
35 pages
English language
sale 15% off
Draft
33 pages
English language
sale 15% off

ISO

ISO 21219-1:2023(Main)

Intelligent transport systems — Traffic and travel information (TTI) via transport protocol experts group, generation 2 (TPEG2) — Part 1: Introduction, numbering and versions (TPEG2-INV)

This document defines an index to the complete set of TPEG Generation 2 toolkit components and applications. New applications are enumerated with an application identification (AID) as they are added to the TPEG applications family. NOTE 1 This document will be updated when new applications occur in order to indicate the latest status and the inter-working of the various TPEG specifications. This document will be revised as a new edition every time a new issue of any other specification is issued. NOTE 2 Preliminary AIDs are allocated and managed by TISA and are listed at Reference.

Standard
9 pages
English language
sale 15% off

ISO

ISO 23375:2023(Main)

Intelligent transport systems — Collision evasive lateral manoeuvre systems (CELM) — Requirements and test procedures

This document specifies basic control strategies, minimum functional requirements, basic driver interface elements, and test procedures for verifying the system requirements for collision evasive lateral manoeuvre systems (CELM). A CELM is a safety system aimed at supporting the driver’s vehicle operation by avoiding collisions with objects in the forward path of the vehicle. When a collision is predicted, the CELM controls lateral movement of the vehicle by generating yaw moment. The lateral control manoeuvres can be performed automatically by CELM or can be initiated by the driver and supported by CELM. Specific methods for object detection and other environmental perception technologies are not described in this document. This document applies to light vehicles and heavy trucks. Vehicles equipped with trailers are not within the scope of this document.

Standard
31 pages
English language
sale 15% off

ISO

ISO/TR 5255-2:2023(Main)

Intelligent transport systems — Low-speed automated driving system (LSADS) service — Part 2: Gap analysis

This document: — examines and analyses the safety environment for low-speed automated driving services (LSADS); — describes the safety role supplement to the functional model described in ISO/TS 5255-1; — describes the supplemental safety points for LSADS; — describes role for the functional model of service applications for LSADS. This document can contribute to the development of future automated driving system service safety requirement use cases, other than the one described in ISO/TS 5255-1. This document is applicable to services using LSADS-equipped vehicles only. In-vehicle control system is not in scope of this document.

Technical report
9 pages
English language
sale 15% off
Technical report
9 pages
English language
sale 15% off