SIST EN 16602-60-13:2023
(Main)Space product assurance - Commercial electrical, electronic and electromechanical (EEE) components
Space product assurance - Commercial electrical, electronic and electromechanical (EEE) components
This standard defines the requirements for selection, control, procurement and
usage of EEE commercial components for space projects.
This standard is applicable to commercial parts from the following families:
• Ceramic capacitors chips
• Solid electrolyte tantalum capacitors chips
• Discrete parts (transistors, diodes, optocouplers)
• Fuses
• Magnetic parts
• Microcircuits
• Resistors chips
• Thermistors
In addition for families of EEE components not addressed by the present ECSS
standard, it can be used as guideline on case by case basis.
The requirements of this document are applicable to all parties involved at all
levels in the integration of EEE commercial components into space segment
hardware and launchers.
This standard may be tailored for the specific characteristics and constrains of a
space project in conformance with ECSS-S-ST-00
Raumfahrtproduktsicherung - Kommerzielle Elektrische, elektronische und elektromechanische (EEE) Bauteile
The purpose of this NWIP is to update EN 16602-60-13(2015), equivalent to ECSS-Q-ST-60-13C “Space product assurance - Commercial electrical, electronic and electromechanical (EEE) components”.
The objectives of this activity are:
1. To disposition all CRs and propose their implementation.
2. Pre-tailoring:
a. The C version of the ECSS-Q-ST-60-13 standard already provides three classes of EEE COTS components, in line with the ECSS-Q-ST-60C Rev.2, but the need for modification to the current type of Pre-Tailoring shall be discussed by the WG and the result reported to the TA for instructions.
b In case the WG believe there will be a need for modification to the current Pre-Tailoring, they will present their request to the TA and specific instructions will be provided.
3. To improve the general usability of the standard by defining requirement rationale where necessary, as specified in Annex B of the present document. The way this information will be published is still to be defined by the TA. The result shall be recorded in a separate document until further instruction by TA.
Justification:
Change Requests have been issued and reviewed by the discipline TAAR. The TA, based on the TAAR assessment, concluded that some of them are important enough and urgent and, as a consequence, required an update of the document.
All CRs recorded on this document shall then be reviewed and implemented by the Policy & Standards Working Group (PSWG) of ESCC that can be supported, if needed, by additional COTS experts that can be properly proposed by the PSWG and approved by the TA and the activities listed in clause 1 shall be carried out.
As identified by the Task Force on New Space Activities, the use of COTS in the current evolving equipment technology is becoming massive and the possibility to use EEE components coming from different business types (Automotive, Aeronautic, Railway, etc.) shall be taken into account .
In addition to the small technical and editorial modifications of Q-ST-60-13C requirements which have been proposed by the attached CRs, the additional following main technical topics have been identified as needed to be implemented:
- Enlargement of ECSS-Q-ST-60-13C Rev.1 to passive parts: enlarging the scope of the ECSS-Q-ST-60-13 current issue, by adding requirements about passive parts procurement (the scope of the current issue is limited to active parts).
- Automotive standard recognition: This new work item proposal aimed at defining the way to recognize automotive standards (AEC-Q) in EEE parts procurement process.
- Screening and re-tinning requirements modification: This new work item proposal aimed at reducing screening and re-tinning requirements in certain cases.
Assurance produit des projets spatiaux - Composants électriques, électroniques et électromécaniques (EEE) commerciaux
Zagotavljanje varnih proizvodov v vesoljski tehniki - Električne, elektronske in elektromehanske komercialne komponente (EEE)
Ta standard določa zahteve za izbiro, nadzor, nabavo in uporabo komercialnih električnih, elektronskih in elektromehanskih komponent (EEE) za vesoljske projekte.
Ta standard se uporablja za komercialne dele iz naslednjih skupin:
• čipi keramičnega kondenzatorja,
• čipi tantalskega kondenzatorja s trdnim elektrolitom,
• diskretni deli (tranzistorji, diode, optični sklopniki),
• varovalke,
• magnetni deli,
• mikrovezja,
• uporni čipi,
• termistorji.
Poleg tega se lahko za družine električnih, elektronskih in elektromehanskih komponent (EEE), ki jih ta standard ECSS ne obravnava, uporablja kot smernica za vsak primer posebej.
Zahteve tega dokumenta veljajo za vse vpletene strani na vseh ravneh integracije komercialnih električnih, elektronskih in elektromehanskih komponent v vesoljski strojni opremi in lansirnikih.
Ta standard se lahko prilagodi posameznim lastnostim in omejitvam vesoljskega projekta v skladu s standardom ECSS-S-ST-00.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 16602-60-13:2023
01-september-2023
Zagotavljanje varnih proizvodov v vesoljski tehniki - Električne, elektronske in
elektromehanske komercialne komponente (EEE)
Space product assurance - Commercial electrical, electronic and electromechanical
(EEE) components
Raumfahrtproduktsicherung - Kommerzielle Elektrische, elektronische und
elektromechanische (EEE) Bauteile
Assurance produit des projets spatiaux - Composants électriques, électroniques et
électromécaniques (EEE) commerciaux
Ta slovenski standard je istoveten z: EN 16602-60-13:2023
ICS:
49.140 Vesoljski sistemi in operacije Space systems and
operations
SIST EN 16602-60-13:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 16602-60-13:2023
---------------------- Page: 2 ----------------------
SIST EN 16602-60-13:2023
EUROPEAN STANDARD EN 16602-60-13
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2023
ICS 49.140
Supersedes EN 16602-60-13:2015
English version
Space product assurance - Commercial electrical,
electronic and electromechanical (EEE) components
Assurance produit des projets spatiaux - Composants Raumfahrtproduktsicherung - Kommerzielle
électriques, électroniques et électromécaniques (EEE) Elektrische, elektronische und elektromechanische
commerciaux (EEE) Bauteile
This European Standard was approved by CEN on 30 January 2023.
CEN and CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical
references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to
any CEN and CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN and CENELEC member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN and CENELEC members are the national standards bodies and national electrotechnical committees of Austria, Belgium,
Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia,
Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and United Kingdom.
CEN-CENELEC Management Centre:
Rue de la Science 23, B-1040 Brussels
© 2023 CEN/CENELEC All rights of exploitation in any form and by any means
Ref. No. EN 16602-60-13:2023 E
reserved worldwide for CEN national Members and for
CENELEC Members.
---------------------- Page: 3 ----------------------
SIST EN 16602-60-13:2023
EN 16602-60-13:2023 (E)
Table of contents
European Foreword . 5
Introduction . 6
1 Scope . 8
2 Normative references . 9
3 Terms, definitions and abbreviated terms . 11
3.1 Terms from other standards .11
3.2 Terms specific to the present standard .11
3.3 Abbreviated terms. 12
3.4 Conventions.13
3.5 Nomenclature .14
3.6 Convention for the Applicability Matrix . 15
4 Requirements for class 1 components . 16
5 Requirements for class 2 components . 28
6 Requirements for class 3 components . 39
7 Quality levels . 50
8 Evaluation, screening and LAT tests . 51
9 Pure tin lead finish – risk analysis . 93
Annex A (normative) Component control plan (
...
SLOVENSKI STANDARD
oSIST prEN 16602-60-13:2021
01-november-2021
Nadomešča:
SIST EN 16602-60-13:2015
Zagotavljanje varnih proizvodov v vesoljski tehniki - Zahteve za uporabo COST-
komponent
Space product assurance - Commercial electrical, electronic and electromechanical
(EEE) components
Raumfahrtproduktsicherung - Anforderungen für die Nutzung von COTS-Komponenten
Assurance produit des projets spatiaux - Exigences pour l'utilisation de composants
commerciaux sur étagère
Ta slovenski standard je istoveten z: prEN 16602-60-13
ICS:
49.140 Vesoljski sistemi in operacije Space systems and
operations
oSIST prEN 16602-60-13:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 16602-60-13:2021
---------------------- Page: 2 ----------------------
oSIST prEN 16602-60-13:2021
EUROPEAN STANDARD
DRAFT
prEN 16602-60-13
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2021
ICS 49.140
Will supersede EN 16602-60-13:2015
English version
Space product assurance - Commercial electrical,
electronic and electromechanical (EEE) components
Assurance produit des projets spatiaux - Exigences Raumfahrtproduktsicherung - Anforderungen für die
pour l'utilisation de composants commerciaux sur Nutzung von COTS-Komponenten
étagère
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/CLC/JTC 5.
If this draft becomes a European Standard, CEN and CENELEC members are bound to comply with the CEN/CENELEC Internal
Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any
alteration.
This draft European Standard was established by CEN and CENELEC in three official versions (English, French, German). A
version in any other language made by translation under the responsibility of a CEN and CENELEC member into its own
language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN and CENELEC members are the national standards bodies and national electrotechnical committees of Austria, Belgium,
Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia,
Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.Recipients of this draft are invited to submit, with their comments, notification
of any relevant patent rights of which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
---------------------- Page: 3 ----------------------
oSIST prEN 16602-60-13:2021
prEN 16602-60-13:2021 (E)
Table of contents
European Foreword . 5
Introduction . 6
1 Scope . 8
2 Normative references . 9
3 Terms, definitions and abbreviated terms . 11
3.1 Terms from other standards . 11
3.2 Terms specific to the present standard . 11
3.3 Abbreviated terms. 11
3.4 Conventions. 13
3.5 Nomenclature . 14
4 Requirements for class 1 components . 15
5 Requirements for class 2 components . 35
6 Requirements for class 3 components . 53
7 Quality levels . 70
8 Procurement test table . 71
9 Pure tin lead finish – risk analysis .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.