Powered industrial trucks - Visibility-test methods and verification - Part 8: Stand-on counterbalance trucks up to and including 10 000 kg capacity

This document specifies the requirements and test procedures for 360° visibility of stand-on counterbalance trucks with a capacity up to and including 10 000 kg in accordance with ISO 5053 1 (herein after referred to as trucks) without a load and it is intended to be used in conjunction with EN 16842-1.
Where specific requirements in this document are modified from the general requirements in EN 16842 1, the requirements of this document are truck-specific and are to be used for stand-on counterbalance trucks with a capacity up to, and including, 10 000 kg.
This part of EN 16842 deals with all significant hazards, hazardous situations or hazardous events, relevant to the visibility of the operator for applicable machines when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.

Kraftbetriebene Flurförderzeuge - Sichtverhältnisse - Prüfverfahren und Verifikation - Teil 8: Gegengewichtstapler mit stehendem Bediener bis einschließlich einer Nenntragfähigkeit von 10 000 kg

Dieses Dokument legt die Anforderungen und Prüfverfahren für die Rundumsicht (360°) von Gegengewichtstaplern ohne Fahrersitz mit einer Nenntragfähigkeit bis einschließlich 10 000 kg in Übereinstimmung mit ISO 5053 1 (hier als Flurförderzeuge bezeichnet) fest und ist dafür vorgesehen, in Verbindung mit EN 16842 1 angewendet zu werden.
Wenn spezifische Anforderungen in diesem Dokument von den allgemeinen Anforderungen in EN 16842 1 abweichen, sind die Anforderungen in diesem Dokument für das Flurförderzeug spezifisch und für Gegengewichtstapler ohne Fahrersitz mit einer Nenntragfähigkeit bis einschließlich 10 000 kg anzuwenden.
Dieser Teil von EN 16842 behandelt alle signifikanten Gefährdungen, Gefährdungssituationen oder Gefährdungsereignisse, die für die Sichtverhältnisse des Bedieners der betreffenden Maschinen relevant sind, wenn sie bestimmungsgemäß und unter Bedingungen, die vom Hersteller als Fehlanwendung vernünftigerweise vorhersehbar sind, verwendet werden.

Chariots de manutention automoteurs - Visibilité - Méthodes d'essai et vérification - Partie 8 : Chariots en porte-à-faux à conducteur debout ayant une capacité jusqu'à 10 000 kg inclus

Le présent document spécifie les prescriptions et les modes opératoires d’essai relatifs à la visibilité sur 360° des chariots de manutention en porte-à-faux à conducteur debout ayant une capacité jusqu'à 10 000 kg inclus conformes à l'ISO 5053 1 (ci-après désignés chariots), sans charge et il est destiné à être utilisé conjointement avec l’EN 16842-1.
Lorsque des prescriptions spécifiques du présent document sont modifiées par rapport aux prescriptions générales de l'EN 16842 1, les prescriptions du présent document sont spécifiques au chariot et sont à utiliser pour les chariots en porte-à-faux à conducteur debout ayant une capacité jusqu'à 10 000 kg inclus.
La présente partie de l'EN 16842 traite de tous les phénomènes dangereux, situations dangereuses ou événements dangereux significatifs relatifs à la visibilité de l’opérateur pour les machines concernées lorsqu'elles sont utilisées comme prévu et dans des conditions de mauvaise utilisation raisonnablement prévisible par le fabricant.

Vozila za talni transport - Gnana vozila za talni transport - Vidno polje voznika - Preskusne metode in preverjanje - 8. del: Čelni viličar s stoječim upravljavcem in z nosilnostjo do 10 000 kg

General Information

Status
Published
Public Enquiry End Date
15-Dec-2019
Publication Date
15-Feb-2021
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
21-Jan-2021
Due Date
28-Mar-2021
Completion Date
16-Feb-2021

Buy Standard

Standard
SIST EN 16842-8:2021
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Draft
oSIST prEN 16842-8:2019
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 16842-8:2021
01-april-2021

Vozila za talni transport - Gnana vozila za talni transport - Vidno polje voznika -

Preskusne metode in preverjanje - 8. del: Čelni viličar s stoječim upravljavcem in z

nosilnostjo do 10 000 kg

Powered industrial trucks - Visibility-test methods and verification - Part 8: Stand-on

counterbalance trucks up to and including 10 000 kg capacity

Kraftbetriebene Flurförderzeuge - Sichtverhältnisse - Prüfverfahren und Verifikation - Teil

8: Gegengewichtstapler mit stehendem Bediener bis einschließlich einer
Nenntragfähigkeit von 10 000 kg

Chariots de manutention automoteurs - Visibilité - Méthodes d'essai et vérification -

Partie 8 : Chariots en porte-à-faux à conducteur debout ayant une capacité jusqu'à 10

000 kg inclus
Ta slovenski standard je istoveten z: EN 16842-8:2021
ICS:
53.060 Industrijski tovornjaki Industrial trucks
SIST EN 16842-8:2021 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 16842-8:2021
---------------------- Page: 2 ----------------------
SIST EN 16842-8:2021
EN 16842-8
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2021
EUROPÄISCHE NORM
ICS 53.060
English Version
Powered industrial trucks - Visibility-Test methods and
verification - Part 8: Stand-on counterbalance trucks up to
and including 10 000 kg capacity

Chariots de manutention automoteurs - Visibilité - Kraftbetriebene Flurförderzeuge - Sichtverhältnisse -

Méthodes d'essai et vérification - Partie 8 : Chariots en Prüfverfahren und Verifikation - Teil 8:

porte-à-faux à conducteur debout ayant une capacité Gegengewichtstapler mit stehendem Bediener bis

jusqu'à 10 000 kg inclus einschließlich einer Nenntragfähigkeit von 10 000 kg
This European Standard was approved by CEN on 6 December 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16842-8:2021 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 16842-8:2021
EN 16842-8:2021 (E)
Contents Page

European foreword ...................................................................................................................................................... 3

Introduction .................................................................................................................................................................... 5

1 Scope .................................................................................................................................................................... 6

2 Normative references .................................................................................................................................... 6

3 Terms and definitions ................................................................................................................................... 6

4 Truck Configuration ....................................................................................................................................... 6

4.1 General................................................................................................................................................................ 6

4.2 Fork arm dimension ...................................................................................................................................... 7

5 Test equipment ................................................................................................................................................ 7

6 Test procedures for direct visibility ........................................................................................................ 7

6.1 General................................................................................................................................................................ 7

6.2 Lighting equipment position ...................................................................................................................... 7

6.3 Test paths for stand-on counterbalance trucks ≤ 10 000 kg capacity ......................................... 9

6.4 Measurement procedure ........................................................................................................................... 12

6.5 Test procedure for indirect visibility ................................................................................................... 12

7 Acceptance criteria...................................................................................................................................... 12

7.1 General............................................................................................................................................................. 12

7.2 Direct visibility ............................................................................................................................................. 12

7.3 Indirect visibility .......................................................................................................................................... 12

7.4 Criteria for stand-on counterbalance trucks up to and including 10 000 kg rated

capacity ............................................................................................................................................................ 13

8 Test report ...................................................................................................................................................... 15

9 Information for use ..................................................................................................................................... 15

---------------------- Page: 4 ----------------------
SIST EN 16842-8:2021
EN 16842-8:2021 (E)
European foreword

This document (EN 16842-8:2021) has been prepared by Technical Committee CEN/TC 150 “Industrial

trucks – Safety”, the secretariat of which is held by BSI.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by July 2021, and conflicting national standards shall be

withdrawn at the latest by July 2021.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document is intended to be used in combination with the requirements in EN 16842-1.

The EN 16842 series consists of the following parts under the general title “Powered industrial trucks -

Visibility – Test methods and verification”:
— Part 1: General requirements;

— Part 2: Sit-on counterbalance trucks and rough terrain masted trucks up to and including 10 000 kg

capacity;
— Part 3: Reach trucks up to and including 10 000 kg capacity;

— Part 4: Industrial variable reach trucks up to and including 10 000 kg capacity;

— Part 5: Industrial variable reach trucks greater than 10 000 kg capacity;

— Part 6: Sit-on counterbalance trucks and rough terrain masted trucks greater than 10 000 kg capacity;

— Part 7: Variable reach and masted container trucks handling freight containers of 6 m (20 ft) length

and longer;
— Part 8: Stand on counterbalance trucks up to and including 10 000 kg capacity;

— Part 9: Order picking lateral- and front stacking trucks with elevating operator position;

— Part 10: Towing and Pushing tractors and Burden carrier.
It is intended to develop the parts related to the following machinery:
— Pallet stacking trucks (rider controlled);
— Single side loader;
— Multi-directional forklift truck;
— Articulated counterbalance lift truck;
— Non-stacking low-lift straddle carrier (as defined in ISO 5053-1:2020, 3.18);
— Stacking high-lift straddle carrier (as defined in ISO 5053-1:2020, 3.19).
---------------------- Page: 5 ----------------------
SIST EN 16842-8:2021
EN 16842-8:2021 (E)

According to the CEN-CENELEC Internal Regulations, the national standards organisations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,

Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,

Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North

Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United

Kingdom.
---------------------- Page: 6 ----------------------
SIST EN 16842-8:2021
EN 16842-8:2021 (E)
Introduction
This document is a Type-C standard as stated in EN ISO 12100.

This document is of relevance, in particular, for the following stakeholder groups representing the market

players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);

— health and safety bodies (regulators, accident prevention organizations, market surveillance, etc.).

Others can be affected by the level of machinery safety achieved with the means of the document by the

above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);

— machine users/employees (e.g. trade unions, organizations for people with special needs);

— service providers, e.g. for maintenance (small, medium and large enterprises);
— consumers (in case of machinery intended for use by consumers).

The above-mentioned stakeholder groups have been given the possibility to participate at the drafting

process of this document.

The machinery concerned and the extent to which hazards, hazardous situations or hazardous events are

covered are indicated in the Scope of this document.

When requirements of this type-C standard are different from those which are stated in type-A or type-B

standards, the requirements of this type-C standard take precedence over the requirements of the other

standards for machines that have been designed and built according to the requirements of this type-C

standard.
---------------------- Page: 7 ----------------------
SIST EN 16842-8:2021
EN 16842-8:2021 (E)
1 Scope

This document specifies the requirements and test procedures for 360° visibility of stand-on

counterbalance trucks with a capacity up to and including 10 000 kg in accordance with ISO 5053-1

(herein after referred to as trucks) without a load and it is intended to be used in conjunction with

EN 16842-1.

Where specific requirements in this part are modified from the general requirements in EN 16842-1, the

requirements of this part are truck-specific and to be used for stand-on counterbalance trucks with a

capacity up to and including 10 000 kg.

This part of EN 16842 deals with all significant hazards, hazardous situations or hazardous events,

relevant to the visibility of the operator for applicable machines when used as intended and under

conditions of misuse which are reasonably foreseeable by the manufa
...

SLOVENSKI STANDARD
oSIST prEN 16842-8:2019
01-december-2019

Vozila za talni transport - Gnana vozila za talni transport - Vidno polje voznika -

Preskusna metoda in preverjanje - 8. del: Čelni viličar s stoječim upravljavcem in z

nosilnostjo do 10 000 kg

Powered industrial trucks - Visibility-test methods and verification - Part 8: Stand-on

counterbalance trucks up to and including 10 000 kg capacity

Kraftbetriebene Flurförderzeuge - Sichtverhältnisse - Prüfverfahren und Verifikation - Teil

8: Gegengewichtstapler mit stehendem Bediener bis einschließlich einer
Nenntragfähigkeit von 10 000 kg

Chariots de manutention - Visibilité - Méthode d'essai et vérification - Partie 8 : Chariots

en porte-à-faux à conducteur debout ayant une capacité jusqu'à 10 000 kg inclus
Ta slovenski standard je istoveten z: prEN 16842-8
ICS:
53.060 Industrijski tovornjaki Industrial trucks
oSIST prEN 16842-8:2019 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 16842-8:2019
---------------------- Page: 2 ----------------------
oSIST prEN 16842-8:2019
DRAFT
EUROPEAN STANDARD
prEN 16842-8
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2019
ICS 53.060
English Version
Powered industrial trucks - Visibility-test methods and
verification - Part 8: Stand-on counterbalance trucks up to
and including 10 000 kg capacity

Chariots de manutention - Visibilité - Méthode d'essai Kraftbetriebene Flurförderzeuge - Sichtverhältnisse -

et vérification - Partie 8 : Chariots en porte-à-faux à Prüfverfahren und Verifikation - Teil 8:

conducteur debout ayant une capacité jusqu'à 10 000 Gegengewichtstapler mit stehendem Bediener bis

kg inclus einschließlich einer Nenntragfähigkeit von 10 000 kg

This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee

CEN/TC 150.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations

which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC

Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are

aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without

notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16842-8:2019 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 16842-8:2019
prEN 16842-8:2019 (E)
Contents Page

European foreword .................................................................................................................................................... 3

Introduction .................................................................................................................................................................. 4

1 Scope .................................................................................................................................................................. 5

2 Normative references .................................................................................................................................. 5

3 Terms and definitions ................................................................................................................................. 5

4 Truck Configuration ..................................................................................................................................... 5

4.1 General.............................................................................................................................................................. 5

4.2 Fork arm dimension .................................................................................................................................... 6

5 Test equipment .............................................................................................................................................. 6

6 Test procedures for direct visibility ...................................................................................................... 6

6.1 General.............................................................................................................................................................. 6

6.2 Lighting equipment position .................................................................................................................... 6

6.3 Test paths for stand-on counterbalance trucks ≤ 10 000 kg capacity ....................................... 8

6.4 Measurement procedure ......................................................................................................................... 10

6.5 Test procedure for indirect visibility ................................................................................................. 11

7 Acceptance criteria.................................................................................................................................... 11

7.1 General........................................................................................................................................................... 11

7.2 Direct visibility ........................................................................................................................................... 11

7.2.1 General........................................................................................................................................................... 11

7.2.2 Travelling visibility ................................................................................................................................... 11

7.2.3 Manoeuvring visibility ............................................................................................................................. 11

7.2.4 Fork arms ...................................................................................................................................................... 11

7.3 Indirect visibility ........................................................................................................................................ 11

7.4 Criteria for stand-on counterbalance trucks up to and including 10 000 kg rated

capacity .......................................................................................................................................................... 12

8 Test report .................................................................................................................................................... 14

9 Information for use ................................................................................................................................... 14

---------------------- Page: 4 ----------------------
oSIST prEN 16842-8:2019
prEN 16842-8:2018 (E)
European foreword

This document (prEN 16842-8:2019) has been prepared by Technical Committee CEN/TC 150 “Industrial

trucks – Safety”, the secretariat of which is held by BSI.
This document is currently submitted to the CEN Enquiry.

This document is intended to be used in combination with the requirements in EN 16842-1.

The EN 16842 series consists of the following parts under the general title “Powered industrial trucks –

Visibility – Test methods and verification”:
— Part 1: General requirements;

— Part 2: Sit-on counterbalance trucks and rough terrain masted trucks up to and including 10 000 kg

capacity;
— Part 3: Reach trucks up to and including 10 000 kg capacity;

— Part 4: Industrial variable reach trucks up to and including 10 000 kg capacity;

— Part 5: Industrial variable reach trucks greater than 10 000 kg capacity;

— Part 6: Sit-on counterbalance trucks and rough terrain masted trucks greater than 10 000 kg capacity;

— Part 7: Variable reach and masted container trucks handling freight containers of 6 m (20 ft) length

and longer;

— Part 8: Stand on counterbalance trucks up to and including 10 000 kg capacity (this document);

— Part 9: Order picking lateral- and front stacking trucks with elevating operator position;

— Part 10: Towing and Pushing tractors and Burden carrier.
It is intended to develop the parts related to the following machinery:
— Pallet stacking trucks (rider controlled);
— Single side loader;
— Multi-directional forklift truck;
— Articulated counterbalance lift truck;
— Non-stacking low-lift straddle carrier (as defined in ISO 5053-1:2015, 3.18);
— Stacking high-lift straddle carrier (as defined in ISO 5053-1:2015, 3.19).
---------------------- Page: 5 ----------------------
oSIST prEN 16842-8:2019
prEN 16842-8:2019 (E)
Introduction
This document is a Type-C standard as stated in EN ISO 12100.

This document is of relevance, in particular, for the following stakeholder groups representing the market

players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);

— health and safety bodies (regulators, accident prevention organizations, market surveillance, etc.).

Others can be affected by the level of machinery safety achieved with the means of the document by the

above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);

— machine users/employees (e.g. trade unions, organizations for people with special needs);

— service providers, e.g. for maintenance (small, medium and large enterprises);
— consumers (in case of machinery intended for use by consumers).

The above-mentioned stakeholder groups have been given the possibility to participate at the drafting

process of this document.

The machinery concerned and the extent to which hazards, hazardous situations or hazardous events are

covered are indicated in the Scope of this document.

When requirements of this type-C standard are different from those which are stated in type-A or type-B

standards, the requirements of this type-C standard take precedence over the requirements of the other

standards for machines that have been designed and built according to the requirements of this type-C

standard.
---------------------- Page: 6 ----------------------
oSIST prEN 16842-8:2019
prEN 16842-8:2018 (E)
1 Scope

This document specifies the requirements and test procedures for 360° visibility of stand-on

counterbalance trucks with a capacity up to and including 10 000 kg in accordance with ISO 5053-1

(herein after referred to as trucks) without a load and it is intended to be used in conjunction with

EN 16842-1.

Where specific requirements in this document are modified from the general requirements in

EN 16842-1, the requirements of this document are truck-specific and are to be used for stand-on

counterbalance trucks with a capacity up to, and including, 10 000 kg.

This part of EN 16842 deals with all significant hazards, hazardous situations or hazardous events,

relevant to the visibility of the operator for applicable machines when
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.