SIST EN 62442-1:2012
Energy performance of lamp control gear - Part 1: Control gear for fluorescent lamps - Method of measurement to dertermine the total input power of control gear circuits and the efficiency of the control gear
Energy performance of lamp control gear - Part 1: Control gear for fluorescent lamps - Method of measurement to dertermine the total input power of control gear circuits and the efficiency of the control gear
This part of IEC 62442 defines a measurement and calculation method of the total input power for controlgear ? lamp circuits when operating with their associated fluorescent lamp(s). The calculation method for the efficiency of the lamp controlgear is also defined. This International Standard applies to electrical controlgear lamp circuits consisting only of the controlgear and the lamp(s). It is intended for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz.
Energieeffizienz von Lampenbetriebsgeräten - Teil 1: Betriebsgeräte für Leuchtstofflampen - Messverfahren zur Bestimmung der Gesamteingangsleistung von Betriebsgeräteschaltungen und des Wirkungsgrades von Betriebsgeräten
Performance énergétique des appareillages de lampes - Partie 1: Appareillages des lampes à fluorescence - Méthode de mesure pour la détermination de la puissance d'entrée totale des circuits d'appareillage et du rendement des appareillages
La CEI 62442-1:2011 définit une méthode de mesure et de calcul de la puissance d'entrée totale pour les circuits appareillage - lampe fonctionnant avec la ou les lampes à fluorescence qui leur sont associées. La méthode de calcul du rendement des appareillages de lampe est également définie. La présente Norme internationale s'applique aux circuits constitués exclusivement d'appareillages électriques et de lampes. Elle s'applique à des alimentations alternatives de 1 000 V au maximum, à 50 Hz ou 60 Hz.
Energijske lastnosti krmilne naprave sijalke - 1. del: Krmilna naprava za fluorescentne sijalke - Merilna metoda za ugotavljanje celotne vhodne moči krmilnih vezij in izkoristka krmilne naprave
Ta del IEC 62442 določa merilno in računsko metodo za ugotavljanje celotne vhodne moči za krmilna vezja sijalk, kadar delujejo s povezanimi fluorescenčnimi sijalkami. Prav tako je določena računska metoda za učinkovitost krmilne naprave sijalke. Ta mednarodni standard velja za električne krmilne naprave vezij sijalk, sestavljenih samo iz krmilne naprave in sijalk(-e). Namenjen je za uporabo pri izmenični napetosti, nižji od 1000 V, pri 50 Hz ali 60 Hz.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 62442-1:2012
01-januar-2012
(QHUJLMVNHODVWQRVWLNUPLOQHQDSUDYHVLMDONHGHO .UPLOQDQDSUDYD]D
IOXRUHVFHQWQHVLMDONH0HULOQDPHWRGD]DXJRWDYOMDQMHFHORWQHYKRGQHPRþL
NUPLOQLKYH]LMLQL]NRULVWNDNUPLOQHQDSUDYH
Energy performance of lamp control gear - Part 1: Control gear for fluorescent lamps -
Method of measurement to dertermine the total input power of control gear circuits and
the efficiency of the control gear
Energieeffizienz von Lampenbetriebsgeräten - Teil 1: Betriebsgeräte für
Leuchtstofflampen - Messverfahren zur Bestimmung der Gesamteingangsleistung von
Betriebsgeräteschaltungen und des Wirkungsgrades von Betriebsgeräten
Performance énergétique des appareillages de lampes - Partie 1: Appareillages des
lampes à fluorescence - Méthode de mesure pour la détermination de la puissance
d'entrée totale des circuits d'appareillage et du rendement des appareillages
Ta slovenski standard je istoveten z: EN 62442-1:2011
ICS:
29.140.99 Drugi standardi v zvezi z Other standards related to
žarnicami lamps
SIST EN 62442-1:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 62442-1:2012
---------------------- Page: 2 ----------------------
SIST EN 62442-1:2012
EUROPEAN STANDARD
EN 62442-1
NORME EUROPÉENNE
November 2011
EUROPÄISCHE NORM
ICS 29.140.99
English version
Energy performance of lamp controlgear -
Part 1: Controlgear for fluorescent lamps -
Method of measurement to determine the total input power of controlgear
circuits and the efficiency of the controlgear
(IEC 62442-1:2011)
Performance énergétique des Energieeffizienz von
appareillages de lampes - Lampenbetriebsgeräten -
Partie 1: Appareillages des lampes à Teil 1: Betriebsgeräte für
fluorescence - Leuchtstofflampen -
Méthode de mesure pour la détermination Messverfahren zur Bestimmung der
de la puissance d'entrée totale des circuits Gesamteingangsleistung von
d'appareillage et du rendement des Betriebsgeräteschaltungen und des
appareillages Wirkungsgrades von Betriebsgeräten
(CEI 62442-1:2011) (IEC 62442-1:2011)
This European Standard was approved by CENELEC on 2011-11-16. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62442-1:2011 E
---------------------- Page: 3 ----------------------
SIST EN 62442-1:2012
EN 62442-1:2011 - 2 -
Foreword
The text of document 34C/987/FDIS, future edition 1 of IEC 62442-1, prepared by SC 34C, "Auxiliaries for
lamps", of IEC/TC 34, "Lamps and related equipment" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN 62442-1:2011.
The following dates are fixed:
(dop) 2012-08-16
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2014-11-16
• latest date by which the national
standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 62442-1:2011 was approved by CENELEC as a European
Standard without any modification.
---------------------- Page: 4 ----------------------
SIST EN 62442-1:2012
- 3 - EN 62442-1:2011
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60081 - Double-capped fluorescent lamps - EN 60081 -
Performance specifications
IEC 60901 - Single-capped fluorescent lamps - EN 60901 -
Performance specifications
IEC 60921 2004 Ballasts for tubular fluorescent lamps - EN 60921 2004
Performance requirements
IEC 60929 2011 AC and/or DC-supplied electronic control EN 60929 2011
+ corr. September 2011 gear for tubular fluorescent lamps -
Performance requirements
IEC 61347-2-3 - Lamp controlgear - EN 61347-2-3 -
Part 2-3: Particular requirements for a.c.
and/or d.c. supplied electronic control gear for
fluorescent lamps
IEC 61347-2-8 - Lamp controlgear - EN 61347-2-8 -
Part 2-8: Particular requirements for ballasts
for fluorescent lamps
---------------------- Page: 5 ----------------------
SIST EN 62442-1:2012
---------------------- Page: 6 ----------------------
SIST EN 62442-1:2012
IEC 62442-1
®
Edition 1.0 2011-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Energy performance of lamp controlgear –
Part 1: Controlgear for fluorescent lamps – Method of measurement to determine
the total input power of controlgear circuits and the efficiency of the controlgear
Performance énergétique des appareillages de lampes –
Partie 1: Appareillages des lampes à fluorescence – Méthode de mesure pour la
détermination de la puissance d'entrée totale des circuits d'appareillage et du
rendement des appareillages
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX R
ICS 29.140.99 ISBN 978-2-88912-718-4
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 62442-1:2012
– 2 – 62442-1 © IEC:2011
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references. 5
3 Terms and definitions . 6
4 General . 8
4.1 Applicability . 8
4.2 Declaration of ballast lumen factor . 8
4.3 Dimmable controlgear . 8
4.4 Multi-wattage and/or multi-lamp controlgear . 8
4.5 Accuracy of measurement . 8
4.6 Sampling of controlgear for testing . 8
4.7 Number of samples. 9
4.8 Conditioning of lamps . 9
4.9 Test voltages and frequencies . 9
5 Method of measurement and calculation of total input power of controlgear –lamp
circuits and the efficiency of controlgear . 9
5.1 Correction for ballast lumen factor . 9
5.2 Method of measurement . 9
5.3 Measurement and calculation of the total input power of magnetic wire wound
controlgear – lamp circuits . 10
5.4 Calculation of the efficiency of magnetic wire wound controlgear . 10
5.5 Measurement and calculation of the total input power of electronic
controlgear –lamp circuits . 10
5.6 Calculation of the efficiency of electronic controlgear . 12
5.7 Measuring the standby power. 12
Annex A (normative) Energy performance measurement setup . 13
Annex B (informative) Application of the reference ballast when assessing lamps in
electronic operation . 17
Bibliography . 18
Figure 1 – Configuration of lamp and photocell sensor . 12
Figure A.1 – Measurement of magnetic wire wound controlgear – lamp circuits . 13
Figure A.2 – Measurement of a.c. supplied electronic controlgear – lamp circuits . 14
Figure A.3 – Test setup for measuring standby power . 14
Figure A.4 – Side view of light output measurement system . 15
Figure A.5 – Top view of light output measurement system . 15
Table 1 – Typical nominal electricity supply details for some regions . 9
---------------------- Page: 8 ----------------------
SIST EN 62442-1:2012
62442-1 © IEC:2011 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ENERGY PERFORMANCE OF LAMP CONTROLGEAR –
Part 1: Controlgear for fluorescent lamps –
Method of measurement to determine the total input power
of controlgear circuits and the efficiency of the controlgear
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62442-1 has been prepared by subcommittee 34C: Auxiliaries for
lamps, of IEC technical committee 34: Lamps and related equipment.
The text of this standard is based on the following documents:
FDIS Report on voting
34C/987/FDIS 34C/996/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
---------------------- Page: 9 ----------------------
SIST EN 62442-1:2012
– 4 – 62442-1 © IEC:2011
A list of all parts of the IEC 62442 series, published under the general title Energy performance
of lamp controlgear, can be found on the IEC website.
This standard has been drafted in response to support classification systems for lamp
controlgear.
Consideration is being given to include in a future edition of this standard:
– Controlgear ‒ high intensity discharge (HID) lamp circuits;
– Transformer or step-down converter ‒ low voltage halogen lamp circuits;
The committee has decided that the contents of this publication will remain unchanged until the
stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to
the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 10 ----------------------
SIST EN 62442-1:2012
62442-1 © IEC:2011 – 5 –
ENERGY PERFORMANCE OF LAMP CONTROLGEAR –
Part 1: Controlgear for fluorescent lamps –
Method of measurement to determine the total input power
of controlgear circuits and the efficiency of the controlgear
1 Scope
This part of IEC 62442 defines a measurement and calculation method of the total input power
for controlgear ‒ lamp circuits when operating with their associated fluorescent lamp(s). The
calculation method for the efficiency of the lamp controlgear is also defined. This International
Standard applies to electrical controlgear lamp circuits consisting only of the controlgear and
the lamp(s). It is intended for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz.
NOTE Requirements for testing individual controlgear during production are not included.
It specifies the measurement method for the total input power and the calculation method of
the controlgear efficiency for all controlgear used for domestic and normal commercial
purposes operating with the following fluorescent lamps:
– linear fluorescent lamps;
– single-ended (compact) fluorescent lamps;
– other general purpose fluorescent lamps.
This International Standard does not apply to:
– controlgear which form an integral part of the lamp;
– controllable wire-wound magnetic controlgear;
– luminaires, which rely on additional optical performance aspects.
2 Normative references
The following referenced documents are indispensable for the application of this document. For
dated references, only the edition cited applies. For undated references, the latest edition of
the referenced document (including any amendments) applies.
IEC 60081, Double-capped fluorescent lamps – Performance specifications
IEC 60901, Single-capped fluorescent lamps – Performance requirements
IEC 60921:2004, Ballasts for tubular fluorescent lamps – Performance requirements
IEC 60929:2011, AC and/or DC-supplied electronic control gear for tubular fluorescent lamps –
Performance requirements
IEC 61347-2-3, Lamp control gear – Part 2-3: Particular requirements for a.c. and/or d.c.
supplied electronic control gear for fluorescent lamps
IEC 61347-2-8, Lamp controlgear – Part 2-8: Particular requirements for ballasts for
fluorescent lamps
---------------------- Page: 11 ----------------------
SIST EN 62442-1:2012
– 6 – 62442-1 © IEC:2011
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
nominal value
suitable approximate quantity value used to designate or identify a component, device or
equipment
3.2
limiting value
the greatest or smallest admissible value of one of the quantities
3.3
rated value
quantity value for specified operating conditions of a component, device or equipment
The value and conditions are specified in the relevant standard or assigned by the
manufacturer or responsible vendor
NOTE For the different kinds of operation, rated electrical values are given on the lamp data sheets as:
– rated electrical values under “electrical characteristics”, if the lamp is defined for 50 Hz / 60 Hz operation
only,
– rated electrical values under “electrical characteristics”, if the lamp is defined for high frequency (≥ 20 kHz)
operation only,
– rated electrical values and typical electrical values, if the lamp is defined simultaneously for 50 Hz / 60 Hz
operation and high frequency operation
for 50 Hz / 60 Hz operation: rated electrical values under “electrical characteristics”, and
for high frequency operation: rated electrical values under “typical lamp characteristics”.
3.4
controlgear
one or more components between the supply and one or more lamps which may serve to
transform the supply voltage, limit the current of the lamp(s) to the required value, provide
starting voltage and preheating current, prevent cold starting, correct power factor or reduce
radio interference
3.5
electromagnetic controlgear
controlgear which by means of inductance, or a combination of inductance and capacitance,
serves mainly to limit the current of the lamp(s) to the required value
Frequency of the lamp operation is the same as supply frequency.
3.6
electronic controlgear
a.c. and/or d.c. supplied to a.c. invertor including stabilizing elements for starting and operating
one or more tubular fluorescent lamps, generally at high frequency
3.7
fluorescent lamp
discharge lamp of the low pressure mercury type, in which most of the light is emitted by one or
several layers of phosphors excited by the ultra-violet radiation from the discharge
3.8
controlgear – lamp circuit
electrical circuit, or part thereof, normally built in a luminaire, consisting of the controlgear and
lamp(s)
---------------------- Page: 12 ----------------------
SIST EN 62442-1:2012
62442-1 © IEC:2011 – 7 –
3.9
reference ballast
special ballast, either inductive for lamps for operation on a.c. mains frequencies, or resistive
for lamps for operation on high frequency
It is designed for the purpose of providing comp
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.