SIST-TS CEN/TS 13126-15:2005

Building hardware, fittings for windows and door height windows - Requirements and test methods - Part 15: Rollers

This Part of prCEN/TS 13126 gives requirements and test methods for durability, strength, security and function of rollers for windows and door height windows.
This standard is applicable to rollers irrespective of whether they are adjustable or not and of the method or type of fixing or if they are used independently, or in multiples or combinations

Baubeschläge, Beschläge für Fenster und Fenstertüren - Anforderungen und Prüfverfahren - Teil 15: Rollen für Schiebefenster

Dieser Teil von prCEN/TS 13126 legt die Anforderungen und Prüfverfahren für die Dauerfunktionstüchtig-keit, Festigkeit, Schutzwirkung und Funktionsweise von Rollen für Schiebefenster und Fenstertüren fest.
Die vorliegende Technische Spezifikation gilt für Rollen, unabhängig davon, ob sie verstellbar sind oder nicht und unabhängig vom Verfahren oder der Art der Befestigung oder davon, ob sie voneinander unabhängig, vielfach oder in Kombinationen verwendet werden.

Quincaillerie pour le bâtiment, ferrures de fenetres et portes-fenetres - Exigences et méthodes d'essai - Partie 15: Roulements

La présente partie du prCEN/TS 13126 spécifie des exigences et méthodes d'essai relatives a l'endurance, a la résistance et au fonctionnement des roulements pour fenetres et portes-fenetres ainsi qu'a la sécurité des biens.
Cette norme s'applique aux roulements en général, qu'ils soient ou non réglables, qu'ils soient utilisés individuellement ou fassent partie d'un jeu de roulements identiques ou non, et quel que soit le mode.

Stavbno okovje, pritrjevalni sistemi za okna in zastekljena vrata – Zahteve in preskusne metode – 15. del: Valji drsnih oken

General Information

• Status: Withdrawn
• Publication Date: 31-Dec-2004
• Withdrawal Date: 10-Mar-2008
• ICS: 91.190 - Building accessories
• Technical Committee: ISTP - Doors and windows
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 04-Mar-2008
• Due Date: 27-Mar-2008
• Completion Date: 11-Mar-2008
• Directive: 89/106/EEC - Construction products
• Ref Project: CEN/TS 13126-15:2004 - Building hardware, fittings for windows and door height windows - Requirements and test methods - Part 15: Rollers

Relations

• Replaced By: SIST EN 13126-15:2008 - Building hardware - Hardware for windows and balcony doors - Requirements and test methods - Part 15: Rollers for horizontal sliding and sliding folding windows and doors
• Effective Date: 01-May-2008

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-TS CEN/TS 13126-15:2005
01-januar-2005
Stavbno okovje, pritrjevalni sistemi za okna in zastekljena vrata – Zahteve in
preskusne metode – 15. del: Valji drsnih oken
Building hardware, fittings for windows and door height windows - Requirements and test
methods - Part 15: Rollers
Baubeschläge, Beschläge für Fenster und Fenstertüren - Anforderungen und
Prüfverfahren - Teil 15: Rollen für Schiebefenster
Quincaillerie pour le bâtiment, ferrures de fenetres et portes-fenetres - Exigences et
méthodes d'essai - Partie 15: Roulements
Ta slovenski standard je istoveten z: CEN/TS 13126-15:2004
ICS:
91.190
SIST-TS CEN/TS 13126-15:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

TECHNICAL SPECIFICATION
CEN/TS 13126-15
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
April 2004
ICS 91.190
English version
Building hardware, fittings for windows and door height windows
- Requirements and test methods - Part 15: Rollers
Quincaillerie pour le bâtiment, ferrures de fenêtres et Baubeschläge, Beschläge für Fenster und Fenstertüren -
portes-fenêtres - Exigences et méthodes d'essai - Partie Anforderungen und Prüfverfahren - Teil 15: Rollen für
15: Roulements Schiebefenster
This Technical Specification (CEN/TS) was approved by CEN on 18 August 2003 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 13126-15:2004: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

CEN/TS 13126-15:2004 (E)
Contents
Page
Foreword .3
1 Scope.4
2 Normative references.4
3 Terms and definitions.4
4 Classification.5
5 Requirements .6
6 Test apparatus.6
7 Test methods.6
(informative)
Annex A Tests for rollers used in straight sliding windows (types N, P and T) 9
Annex B (informative) Test of rollers used in windows that fold (types Q, R and S) .10
Annex C (normative) Flow chart of test procedures.14
2

---------------------- Page: 3 ----------------------

CEN/TS 13126-15:2004 (E)
Foreword
This document (CEN/TS 13126-15:2004) has been prepared by Technical Committee CEN/TC 33
“Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by
AFNOR.
A full contribution to the preparation of this Technical Specification has been made by the European
manufacturers organisation ‘ARGE’ and National Standards institutions.
This Technical Specification is one of a series of Technical Specifications dedicated to building
hardware products. It is divided into seventeen parts to incorporate all types of windows and door
height windows.
Informative annex A of CEN/TS 13126-1 gives detailed schedules of the elements of components of
the seventeen parts of this Technical Specification.
Normative annex B of CEN/TS 13126-1 gives schedules of the elements of components used on the
21 types of window opening functions.
Normative and informative annex to all parts of this Technical Specification are indicated in the
content of the seventeen parts.
The performance tests incorporated in this standard are considered to be reproducible and as such
will provide a consistent and objective assessment of the performance of these products throughout
CEN Member States.
Annex A and B are informative while annex C is normative.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
3

---------------------- Page: 4 ----------------------

CEN/TS 13126-15:2004 (E)
1 Scope
This Part of CEN/TS 13126 gives requirements and test methods for durability, strength, security and
function of rollers for windows and door height windows.
This standard is applicable to rollers irrespective of whether they are adjustable or not and of the
method or type of fixing or if they are used independently, or in multiples or combinations
2 Normative references
This Technical Specification incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text, and the
publications are listed hereafter. For dated references, subsequent amendments to, or revisions of,
any of these publications apply to this standard only when incorporated in it by amendment or
revision. For undated references, the latest edition of the publication referred to applies (including
amendments).
EN 1670, Building hardware – Corrosion resistance – Requirements and test methods.
EN 12519:2004, Windows and doors - Terminology
CEN/TS 13126-1:2004 Building hardware – Fittings for windows and door height windows –
Requirements and test methods – Requirements common to all types of fittings
prEN 14608, Windows – Determination of the resistance to racking
3 Terms and definitions
For the purposes of this Technical Specification, the terms and definitions given in EN 12519:2004 for
windows and doors and the following apply:
3.1
bogey
assembly of one or more rollers in a single or multiple unit which supports a sliding window whether it
moves in a straight line or rotates about an axis for sliding/folding centre/corner pivoted window and
door height window.
3.2
roll
assembly of one roller which guide a sliding and folding window and door height window centre/corner
pivoted.
4

---------------------- Page: 5 ----------------------

CEN/TS 13126-15:2004 (E)
4 Classification
4.1 General
The classification for rollers shall be in accordance with the requirements of clause 4 in CEN/TS
13126-1:2004
4.2 Category of use (first digit)
No requirement
4.3 Durability (second digit)
Grades shall be in accordance with 4.3 of CEN/TS 13126-1:2004
4.4 Mass (third digit)
Grades shall be in accordance with 4.4 of CEN/TS 13126-1:2004
4.5 Fire resistance (fourth digit)
Grades shall be in accordance with 4.5 of CEN/TS 13126-1:2004
4.6 Safety in use (fifth digit)
Grades shall be in accordance with 4.6 of CEN/TS 13126-1:2004
4.7 Corrosion resistance (sixth digit)
Grades shall b
...