SIST EN ISO 24034:2012
(Main)Welding consumables - Solid wire electrodes, solid wires and rods for fusion welding of titanium and titanium alloys - Classification (ISO 24034:2010)
Welding consumables - Solid wire electrodes, solid wires and rods for fusion welding of titanium and titanium alloys - Classification (ISO 24034:2010)
ISO 24034:2010 specifies requirements for the classification of solid wire electrodes, solid wires and rods for fusion welding of titanium and titanium alloys. The classification is based on their chemical composition.
The compositions of solid wire electrodes for metal inert gas (MIG) welding are the same as solid wire electrodes, solid wires and rods for tungsten inert gas (TIG) arc welding, plasma arc welding, laser beam welding, and other fusion welding processes.
Schweißzusätze - Massivdrahtelektroden, Massivdrähte und Massivstäbe zum Schmelzschweißen von Titan und Titanlegierungen - Einteilung (ISO 24034:2010)
Diese Internationale Norm legt Anforderungen für die Einteilung von Massivdrähten und Massivstäben zum Schmelzschweißen von Titan und Titanlegierungen fest. Die Einteilung der Massivdrähte und Massivstäbe erfolgt nach ihrer chemischen Zusammensetzung.
Bei Titan-Schweißzusätzen weist die Massivdrahtelektrode für den MIG-Prozess (Metall-Inertgasschweißen) dieselbe Zusammensetzung auf wie für den WIG-Prozess (Wolfram-Inertgasschweißen), für den Plasma-Schweißprozess, für den Laserstrahlprozess und für andere Schmelzschweißprozesse. Daher gilt in dieser Einteilungsnorm die Bezeichnung "Massivdrähte/Massivstäbe" sowohl für "Massivdrahtelektroden" als auch für "Massivdrähte und Massivstäbe".
ANMERKUNG In dieser Norm wird der Begriff "Titan" für "Titan und Titan-Legierungen" verwendet.
Die Einteilung der Titan-Massivdrähte und Massivstäbe erfolgt nach ihrer chemischen Zusammensetzung.
Produits consommables pour le soudage - Fils-électrodes pleins, fils pleins et baguettes pleines pour le soudage par fusion du titane et des alliages de titane - Classification (ISO 24034:2010)
L'ISO 24034:2010 spécifie les exigences de classification des fils-électrodes pleins, des fils pleins et des baguettes pleines pour le soudage par fusion du titane et des alliages de titane. La classification est basée sur la composition chimique.
Les compositions des fils-électrodes pleins pour le soudage MIG (soudage à l'arc avec fil-électrode fusible sous gaz inerte) sont identiques aux compositions des fils-électrodes pleins, des fils pleins et des baguettes pleines utilisées pour le soudage TIG (soudage à l'arc avec électrode de tungstène sous gaz inerte), pour le soudage plasma, pour le soudage par faisceau laser, et pour les autres procédés de soudage par fusion.
Dodajni materiali za varjenje - Žične elektrode, žice in palice za talilno varjenje titana in titanovih zlitin - Razvrstitev (ISO 24034:2010)
Ta mednarodni standard določa zahteve za razvrščanje žičnih elektrod, žic in palic za talilno varjenje titana in titanovih zlitin. Razvrščanje temelji na njihovi kemični sestavi. Sestava žičnih elektrod za varjenje s kovinskim inertnim plinom (MIG) je enaka kot sestava žičnih elektrod, žic in palic za obločno varjenje z volframovim inertnim plinom (TIG), plazemsko obločno varjenje, lasersko obločno varjenje in druge postopke talilnega varjenja.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 24034:2012
01-januar-2012
1DGRPHãþD
SIST EN ISO 24034:2006
SIST EN ISO 24034:2006/A1:2008
'RGDMQLPDWHULDOL]DYDUMHQMHäLþQHHOHNWURGHåLFHLQSDOLFH]DWDOLOQRYDUMHQMH
WLWDQDLQWLWDQRYLK]OLWLQ5D]YUVWLWHY ,62
Welding consumables - Solid wire electrodes, solid wires and rods for fusion welding of
titanium and titanium alloys - Classification (ISO 24034:2010)
Schweißzusätze - Massivdrahtelektroden, Massivdrähte und Massivstäbe zum
Schmelzschweißen von Titan und Titanlegierungen - Einteilung (ISO 24034:2010)
Produits consommables pour le soudage - Fils-électrodes pleins, fils pleins et baguettes
pleines pour le soudage par fusion du titane et des alliages de titane - Classification (ISO
24034:2010)
Ta slovenski standard je istoveten z: EN ISO 24034:2010
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
77.120.50 Titan in titanove zlitine Titanium and titanium alloys
SIST EN ISO 24034:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 24034:2012
---------------------- Page: 2 ----------------------
SIST EN ISO 24034:2012
EUROPEAN STANDARD
EN ISO 24034
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2010
ICS 25.160.20 Supersedes EN ISO 24034:2005
English Version
Welding consumables - Solid wire electrodes, solid wires and
rods for fusion welding of titanium and titanium alloys -
Classification (ISO 24034:2010)
Produits consommables pour le soudage - Fils-électrodes Schweißzusätze - Massivdrahtelektroden, Massivdrähte
pleins, fils pleins et baguettes pleines pour le soudage par und Massivstäbe zum Schmelzschweißen von Titan und
fusion du titane et des alliages de titane - Classification Titanlegierungen - Einteilung (ISO 24034:2010)
(ISO 24034:2010)
This European Standard was approved by CEN on 30 September 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 24034:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 24034:2012
EN ISO 24034:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 24034:2012
EN ISO 24034:2010 (E)
Foreword
The text of ISO 24034:2010 has been prepared by Technical Committee ISO/TC 44 “Welding and allied
processes” of the International Organization for Standardization (ISO) and has been taken over as
EN ISO 24034:2010 by Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2011, and conflicting national standards shall be withdrawn at the
latest by April 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 24034:2005.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 24034:2010 has been approved by CEN as a EN ISO 24034:2010 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 24034:2012
---------------------- Page: 6 ----------------------
SIST EN ISO 24034:2012
INTERNATIONAL ISO
STANDARD 24034
Second edition
2010-10-01
Welding consumables — Solid wire
electrodes, solid wires and rods for
fusion welding of titanium and titanium
alloys — Classification
Produits consommables pour le soudage — Fils-électrodes pleins, fils
pleins et baguettes pleines pour le soudage par fusion du titane et des
alliages de titane — Classification
Reference number
ISO 24034:2010(E)
©
ISO 2010
---------------------- Page: 7 ----------------------
SIST EN ISO 24034:2012
ISO 24034:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 24034:2012
ISO 24034:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 24034 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 3, Welding consumables.
This second edition cancels and replaces the first edition (ISO 24034:2005), which has been technically
revised.
Requests for official interpretations of any aspect of this International Standard should be directed to the
Secretariat of ISO/TC 44/SC 3 via your national standards body. A complete listing of these bodies can be
found at www.iso.org.
© ISO 2010 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 24034:2012
ISO 24034:2010(E)
Introduction
This International Standard proposes a classification in order to designate solid wire electrodes, solid wires
and rods in terms of their chemical composition.
There is no unique relationship between the product form (solid wire electrodes, solid wires or rods) and the
welding process used (gas-shielded metal arc welding, tungsten inert gas arc welding, plasma arc welding or
laser beam welding). For this reason, solid wire electrodes, solid wires and rods may be classified in terms of
their chemical composition.
In this International Standard, the symbol of the welding process is not used, because
a) different joining processes are performed with the same chemical component consumable;
b) the producer is not able to determine the process symbol before shipping.
Also, it should be noted that the mechanical properties of all-weld metal test specimens or welded joints
produced by welding consumables will vary from those obtained in production joints because of differences in
welding procedure and the base-metal alloy. For this reason, the mechanical properties of all-weld metal or
welded joints for titanium-welding consumables are not specified in this classification.
iv © ISO 2010 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 24034:2012
INTERNATIONAL STANDARD ISO 24034:2010(E)
Welding consumables — Solid wire electrodes, solid wires
and rods for fusion welding of titanium and titanium alloys —
Classification
1 Scope
This International Standard specifies requirements for the classification of solid wire electrodes, solid wires
and rods for fusion welding of titanium and titanium alloys. The classification is based on their chemical
composition.
The compositions of solid wire electrodes for metal inert gas (MIG) welding are the same as solid wire
electrodes, solid wires and rods for tungsten inert gas (TIG) arc welding, plasma arc welding, laser beam
welding, and other fusion welding processes.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 544, Welding consumables — Technical delivery conditions for filler materials and fluxes — Type of
product, dimensions, tolerances and markings
ISO 14344, Welding consumables — Procurement of filler materials and fluxes
ISO 80000-1:2009, Quantities and units — Part 1:General
3 Classification
The classification is divided into two parts:
a) the first part gives a symbol indicating the product to be identified, see 4.1;
b) the second part gives a symbol indicating the chemical composition of the solid wire electrodes, solid
wires and rods, see Table 1.
4 Symbols and requirements
4.1 Symbol for the product
The symbol for the solid wire electrodes, solid wires and rods shall be S.
© ISO 2010 – All rights reserved 1
---------------------- Page: 11 ----------------------
SIST EN ISO 24034:2012
ISO 24034:2010(E)
4.2 Symbol for the chemical composition
The numerical symbols in Table 1 indicate the chemical composition of a solid wire or rod, determined under
the conditions given in Clause 6. The first two digits indicate the alloy group. See Annex A for an explanation
of the numerical symbols.
The optional additional chemical symbols in Table 1 indicate the chemical composition and include an
indication of the characteristic alloying elements.
5 Mechanical properties
Mechanical properties of all-weld metal or welded joints are not part of this classification.
6 Chemical analysis
Chemical analysis shall be performed on specimens of the product or the stock from which it is made. See
also footnote c to Table 1. Any analytical technique may be used but, in cases of dispute, reference shall be
made to established published methods, agreed between the contracting parties.
7 Rounding procedure
For purposes of determining compliance with the requirements of this International Standard, the actual test
values obtained shall be subjected to the rounding rules of ISO 80000-1:2009, Annex B, Rule A. If the
measured values are obtained by equipment calibrated in units other than those of this International Standard,
the measured values shall be converted to the units of this International Standard before rounding. If an
average value is to be compared to the requirements of this International Standard, rounding shall be done
only after calculating the average. In the case where the testing standard cited in the normative references of
this International Standard contains instructions for rounding that conflict with the instructions of this
International Standard, the rounding requirements of the testing standard shall apply. The rounded-off results
shall fulfil the requirements of the appropriate table for the classification under test.
8 Retest
If any test fails to meet the requirement, that test shall be repeated twice. The results of both retests shall
meet the requirement. Specimens for the retest may be taken from the original test sample or from a new test
sample. For chemical analysis, retests need be only for those specific elements that failed to meet their test
requirement. If the results of one or both retests fail to meet the requirement, the material under test shall be
considered as not meeting the requirements of this specification for that classification.
In the event that, during preparation or after completion of any test, it is clearly determined that prescribed or
proper procedures were not followed in preparing the weld test sample or test specimen(s), or in conducting
the tests, the test shall be considered invalid, without regard to whether the test was actually completed, or
whether the test results met, or failed to meet, the requireme
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.