EN 12413:2019
(Main)Safety requirements for bonded abrasive products
Safety requirements for bonded abrasive products
This document is applicable to rotating bonded abrasive products. It specifies requirements and/or measures for the removal or reduction of hazards resulting from the design and application of the abrasive products.
This document also contains procedures and tests for verification of compliance with the requirements as well as safety information for use, which is to be made available to the user by the manufacturer.
This document does not apply to superabrasive products and coated abrasive products.
Sicherheitsanforderungen für Schleifwerkzeuge aus gebundenem Schleifmittel
Dieses Dokument gilt für rotierende Schleifwerkzeuge aus gebundenem Schleifmittel. Es legt Anforderungen und/oder Maßnahmen zur Beseitigung oder Verringerung von Gefährdungen fest, die von der Gestaltung und Anwendung der Schleifwerkzeuge herrühren.
Dieses Dokument umfasst auch Verfahren und Prüfungen zur Feststellung der Übereinstimmung mit den Anforderungen sowie Benutzerinformationen, die der Hersteller dem Anwender zur Verfügung zu stellen hat.
Dieses Dokument gilt nicht für Schleifwerkzeuge mit Diamant oder Bornitrid als Schleifmittel und nicht für Schleifmittel auf Unterlagen.
Exigences de sécurité pour les produits abrasifs agglomérés
Le présent document est applicable aux produits abrasifs agglomérés en rotation. Il spécifie les prescriptions et/ou mesures pour la suppression ou la réduction des phénomènes dangereux résultant de la conception et de l'utilisation des produits abrasifs.
Le présent document contient également les procédures et les essais pour la vérification de la conformité aux prescriptions aussi bien que les informations de sécurité pour l’utilisation, que le fabricant doit fournir à l’utilisateur.
Le présent document ne s'applique pas aux produits superabrasifs ni aux produits abrasifs appliqués.
Varnostne zahteve za vezana brusilna sredstva
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 12413:2020
01-april-2020
Nadomešča:
SIST EN 12413:2007+A1:2011
Varnostne zahteve za vezana brusilna sredstva
Safety requirements for bonded abrasive products
Sicherheitsanforderungen für Schleifkörper aus gebundenem Schleifmittel
Exigences de sécurité pour les produits abrasifs agglomérés
Ta slovenski standard je istoveten z: EN 12413:2019
ICS:
25.100.70 Brusiva Abrasives
SIST EN 12413:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 12413:2020
---------------------- Page: 2 ----------------------
SIST EN 12413:2020
EN 12413
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2019
EUROPÄISCHE NORM
ICS 25.100.70 Supersedes EN 12413:2007+A1:2011
English Version
Safety requirements for bonded abrasive products
Exigences de sécurité pour les produits abrasifs Sicherheitsanforderungen für Schleifwerkzeuge aus
agglomérés gebundenem Schleifmittel
This European Standard was approved by CEN on 5 August 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12413:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 12413:2020
EN 12413:2019 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions and symbols . 5
4 List of significant hazards . 8
5 Safety requirements . 9
5.1 General requirements . 9
5.1.1 General . 9
5.1.2 Sequence of maximum operating speeds . 9
5.2 Strength requirements . 9
5.2.1 Safety factors. 9
5.2.2 Safety factors for mounted points and wheels . 10
5.2.3 Side load capacity . 10
5.3 Dimensional requirements.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.