EN 13906-3:2001
(Main)Cylindrical helical springs made from round wire and bar - Calculation and design - Part 3: Torsion springs
Cylindrical helical springs made from round wire and bar - Calculation and design - Part 3: Torsion springs
This standard specifies the calculation and design of cold coiled cylindrical helical torsion springs with a linear characteristic, made from round wire and bar of constant diameter with values according to table 1. NOTE Quality Standards for cold coiled torsion springs will be developed later.
Zylindrische Schraubenfedern aus runden Drähten und Stäben - Berechnung und Konstruktion - Teil 3: Drehfedern
Diese Norm gilt für die Berechnung und Konstruktion von kaltgeformten zylindrischen Drehfedern, auch Schenkelfedern genannt, mit linearer Kernlinie aus runden Drähten und Stäben mit konstantem Durchmesser mit Werten nach Tabelle 1. ANMERKUNG Gütenormen für kaltgeformte Drehfedern werden später erarbeitet.
Ressorts hélicoïdaux cylindriques fabriqués à partir de fils ronds et de barres - Calcul et conception - Partie 3: Ressorts de torsion
La présente norme spécifie le calcul et la conception des ressorts de torsion hélicoïdaux cylindriques enroulés à froid de caractéristiques linéaires fabriq qués à partir de fils ronds et de barres, de diamètre constant ayant les valeursdu tableau 1. NOTE Des normes sur la qualité des ressorts de torsion enroulés à froid seront developpées ultérieurement.
Vijačne valjaste vzmeti iz okrogle žice in palic - Izračun in načrtovanje - 3. del: Torzijske vzmeti
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Zylindrische Schraubenfedern aus runden Drähten und Stäben - Berechnung und Konstruktion - Teil 3: DrehfedernRessorts hélicoïdaux cylindriques fabriqués à partir de fils ronds et de barres - Calcul et conception - Partie 3: Ressorts de torsionCylindrical helical springs made from round wire and bar - Calculation and design - Part 3: Torsion springs21.160VzmetiSpringsICS:Ta slovenski standard je istoveten z:EN 13906-3:2001SIST EN 13906-3:2009en,fr,de01-julij-2009SIST EN 13906-3:2009SLOVENSKI
STANDARD
SIST EN 13906-3:2009
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13906-3December 2001ICS 21.160English versionCylindrical helical springs made from round wire and bar -Calculation and design - Part 3: Torsion springsRessorts hélicoïdaux cylindriques fabriqués à partir de filsronds et de barres - Calcul et conception - Partie 3:Ressorts de torsionZylindrische Schraubenfedern aus runden Drähten undStäben - Berechnung und Konstruktion - Teil 3: DrehfedernThis European Standard was approved by CEN on 5 January 2001.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13906-3:2001 ESIST EN 13906-3:2009
EN 13906-3:2001 (E)2ContentsForeword.31Scope.42Normative references.43Terms and definitions, symbols, units and abbreviated terms.43.1Terms and definitions.43.2Symbols, units and abbreviated terms.54Theoretical torsion spring diagram.75Design Principles.105.1General.105.2Design of the ends.105.3Design of the spring body.116Types of loading.116.1Static and quasi-static loading.116.2Dynamic loading.117Stress correction factor q.128Material property values for the calculations of springs.139Design formulate.149.1Design assumptions.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.