EN 12413:2007

Safety requirements for bonded abrasive products

This standard is applicable to rotating bonded abrasive products. It specifies requirements and/or measures for the removal or reduction of hazards resulting from the design and application of the abrasive products.
This standard also contains procedures and tests for verification of compliance with the requirements as well as safety information for use, which is to be made available to the user by the manufacturer.
The hazards taken into consideration are listed in Clause 4 of this standard.
This standard does not apply to superabrasives and coated abrasive products.

Sicherheitsanforderungen für Schleifkörper aus gebundenem Schleifmittel

Diese Norm gilt für rotierende Schleifkörper aus gebundenem Schleifmittel. Sie legt Anforderungen und/oder Maßnahmen zur Beseitigung oder Verringerung von Gefährdungen fest, die von der Gestaltung und Anwendung der Schleifwerkzeuge herrühren.
Diese Norm umfasst auch Verfahren und Prüfungen zur Feststellung der Übereinstimmung mit den Anforderungen sowie Benutzerinformationen, die der Hersteller dem Anwender zur Verfügung zu stellen hat.
Die berücksichtigten Gefährdungen sind in Abschnitt 4 dieser Norm aufgeführt.
Diese Norm gilt nicht für Schleifkörper mit Diamant oder Bornitrid als Schleifmittel und nicht für Schleifmittel auf Unterlagen.

Exigences de sécurité pour les produits abrasifs agglomérés

La présente norme s'applique aux produits abrasifs agglomérés rotatifs. Elle spécifie les exigences et/ou mesures pour la suppression ou la réduction des risques résultant de la conception et de l'application des produits abrasifs.
La présente norme contient également les modes opératoires et les essais permettant de vérifier la conformité avec les exigences ainsi que les informations de sécurité pour l'utilisation que le fabricant doit fournir à l’utilisateur.
Les phénomènes dangereux à prendre en considération sont listés à l'Article 4 de la présente norme.
La présente norme ne s'applique pas aux superabrasifs, ni aux produits abrasifs appliqués.

Varnostne zahteve za vezana brusilna sredstva

General Information

• Status: Withdrawn
• Publication Date: 12-Jun-2007
• Withdrawal Date: 08-Mar-2011
• ICS: 25.100.70 - Abrasives
• Technical Committee: CEN/TC 143 - Machine tools - Safety
• Drafting Committee: CEN/TC 143 - Machine tools - Safety
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 09-Mar-2011
• Completion Date: 09-Mar-2011
• Ref Project: SIST EN 12413:2007 - Safety requirements for bonded abrasive products

Relations

• Replaces: EN 12413:1999 - Safety requirements for bonded abrasive products
• Effective Date: 22-Dec-2008
• Merged Into: EN 12413:2007+A1:2011 - Safety requirements for bonded abrasive products
• Effective Date: 19-Jan-2023
• Amended By: EN 12413:2007/FprA1 - Safety requirements for bonded abrasive products
• Effective Date: 19-Jun-2010

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Safety requirements for bonded abrasive productsVarnostne zahteve za vezana brusilna sredstvaExigences de sécurité pour les produits abrasifs agglomérésSicherheitsanforderungen für Schleifkörper aus gebundenem SchleifmittelTa slovenski standard je istoveten z:EN 12413:2007SIST EN 12413:2007en,fr25.100.70BrusivaAbrasivesICS:SIST EN 12413:20001DGRPHãþDSLOVENSKI
STANDARDSIST EN 12413:200701-september-2007







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12413June 2007ICS 25.100.70Supersedes EN 12413:1999
English VersionSafety requirements for bonded abrasive productsExigences de sécurité pour les produits abrasifsagglomérésSicherheitsanforderungen für Schleifkörper ausgebundenem SchleifmittelThis European Standard was approved by CEN on 10 May 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12413:2007: E



EN 12413:2007 (E) 2 Contents Page Foreword.3 Introduction.4 1 Scope.5 2 Normative references.5 3 Definitions and symbols.5 3.1 Bonded abrasive products.5 3.2 Grinding machines.5 3.3 Grinding method.6 3.4 Type of application.6 3.5 Symbols.7 4 List of significant hazards.8 5 Requirements.8 5.1 General requirements.8 5.2 Strength requirements.9 5.3 Dimensional requirements.10 5.4 Admissible unbalance.30 5.5 Marking.30 5.6 Blotters.30 6 Verification of the requirements and inspection.
...