SIST EN 62639:2012
(Main)Fluorescent induction lamps - Performance requirements
Fluorescent induction lamps - Performance requirements
IEC 62639:2012 specifies the performance requirements for fluorescent induction lamps for general lighting purposes. In this standard, the term 'lamp' stands for 'induction lamp'. It may be expected that lamps which comply with this standard will start and operate satisfactorily at voltages between 92 % and 106 % of rated supply voltage and at an ambient air temperature between 10 °C and 50 °C, when operated with ballasts complying with IEC 60929 and IEC 61347-2-3, as far as applicable, and in a luminaire complying with IEC 60598-1.
Leuchtstoff-Induktionslampen - Anforderungen an die Arbeitsweise
Lampes fluorescentes à induction - Spécification de performance
La CEI 62639:2012 spécifie les exigences de performance des lampes fluorescentes à induction pour l'éclairage général. Dans la présente norme, le terme 'lampe' désigne une 'lampe à induction'. On peut s'attendre à ce que les lampes conformes à la présente norme s'amorcent et fonctionnent de façon satisfaisante à des tensions comprises entre 92 % et 106 % de la tension assignée d'alimentation et à une température ambiante comprise entre 10 °C et 50 °C, lorsqu'elles fonctionnent avec des ballasts conformes à la CEI 60929 et à la CEI 61347-2-3, dans la mesure où cela s'applique, et lorsqu'elles sont installées dans un luminaire conforme à la CEI 60598-1.
Fluorescenčne indukcijske sijalke - Zahteve za delovanje
Ta mednarodni standard določa zahteve za delovanje za fluorescenčne indukcijske sijalke za splošno uporabo v razsvetljavi. V tem standardu izraz »sijalka« pomeni »indukcijske sijalke«. Pričakuje se lahko, da se bodo sijalke, usklajene s tem standardom, prižigale in zadovoljivo delovale pri napetostih od 92 % do 106 % nazivne napajalne napetosti in temperaturi okolja od 10 °C do 50 °C, če so opremljene z dušilko, usklajeno s standardoma IEC 60929 in IEC 61347-2-3, kjer veljata, in nameščene v svetilki, ki je v skladu s standardom IEC 60598-1.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 62639:2012
01-julij-2012
)OXRUHVFHQþQHLQGXNFLMVNHVLMDONH=DKWHYH]DGHORYDQMH
Fluorescent induction lamps - Performance requirements
Leuchtstoff-Induktionslampen - Anforderungen an die Arbeitsweise
Lampes fluorescentes à induction - Spécification de performance
Ta slovenski standard je istoveten z: EN 62639:2012
ICS:
29.140.30 )OXRUHVFHQþQHVLMDONH6LMDONH Fluorescent lamps.
Discharge lamps
SIST EN 62639:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 62639:2012
---------------------- Page: 2 ----------------------
SIST EN 62639:2012
EUROPEAN STANDARD
EN 62639
NORME EUROPÉENNE
April 2012
EUROPÄISCHE NORM
ICS 29.140.30
English version
Fluorescent induction lamps -
Performance specification
(IEC 62639:2012)
Lampes fluorescentes à induction - Leuchtstoff-Induktionslampen -
Spécification de performance Anforderungen an die Arbeitsweise
(CEI 62639:2012) (IEC 62639:2012)
This European Standard was approved by CENELEC on 2012-03-27. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62639:2012 E
---------------------- Page: 3 ----------------------
SIST EN 62639:2012
EN 62639:2012 - 2 -
Foreword
The text of document 34A/1526/FDIS, future edition 1 of IEC 62639, prepared by SC 34A, "Lamps", of
IEC/TC 34, "Lamps and related equipment" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN 62639:2012.
The following dates are fixed:
(dop) 2012-12-27
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2015-03-27
standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 62639:2012 was approved by CENELEC as a European
Standard without any modification.
---------------------- Page: 4 ----------------------
SIST EN 62639:2012
- 3 - EN 62639:2012
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60081 1997 Double-capped fluorescent lamps - EN 60081 1998
Performance specifications
IEC 60598-1 - Luminaires - EN 60598-1 -
Part 1: General requirements and tests
IEC 60929 - AC and/or DC-supplied electronic control gear EN 60929 -
for tubular fluorescent lamps - Performance
requirements
IEC 61347-2-3 - Lamp controlgear - EN 61347-2-3 -
Part 2-3: Particular requirements for a.c.
and/or d.c. supplied electronic control gear for
fluorescent lamps
IEC 62532 2011 Fluorescent induction lamps - Safety EN 62532 2011
specifications
---------------------- Page: 5 ----------------------
SIST EN 62639:2012
---------------------- Page: 6 ----------------------
SIST EN 62639:2012
IEC 62639
®
Edition 1.0 2012-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Fluorescent induction lamps – Performance specification
Lampes fluorescentes à induction – Spécification de performance
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX XB
ICS 29.140.30 ISBN 978-2-88912-920-1
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 62639:2012
– 2 – 62639 IEC:2012
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Lamp requirements . 7
4.1 General . 7
4.2 Marking . 8
4.2.1 General . 8
4.2.2 Correlated colour temperature (CCT) and colour rendering index (R ) . 8
a
4.2.3 Polarity . 8
4.3 Dimensions . 8
4.4 Starting characteristics . 8
4.5 Electrical characteristics . 8
4.6 Photometric characteristics . 8
4.7 Lumen maintenance . 9
4.8 Life . 9
5 Information for ballast design . 9
6 Information for luminaire design . 9
7 Data sheets . 9
7.1 Diagrammatic data sheets for location of lamp dimensions . 9
7.2 Lamp data sheets . 18
7.3 Maximum outline sheets . 44
Annex A (normative) Method of test for starting characteristics . 55
Annex B (normative) Method of test for electrical and photometric characteristics . 57
Annex C (normative) Method of test for lumen maintenance and life . 61
Annex D (informative) Information for ballast design . 62
Annex E (informative) Information for luminaire design . 66
Bibliography . 67
Figure A.1 – Test circuit for measurement of starting characteristics . 56
Figure B.1 – Schematic set-up for measurement of electrical characteristics of
externally coupled induction lamps and photometrical characteristics . 59
Figure B.2 – Example of calorimetric set-up for measurement of power of internally a-
type coupled induction lamps . 60
Figure D.1 – Circuit for testing ballasts – Lamp voltage, lamp current, phase shift and
frequency measured at starting and during operation . 63
Figure D.2 – Circuit for testing ballasts – Lamp voltage, current and frequency
measured at starting . 64
Figure D.3 – Circuit for testing ballasts – Lamp voltage, current, phase shift and
frequency measured during operation . 65
Table A.1 – Frequencies of specially prepared ballasts . 55
---------------------- Page: 8 ----------------------
SIST EN 62639:2012
62639 IEC:2012 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
FLUORESCENT INDUCTION LAMPS –
PERFORMANCE SPECIFICATION
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62639 has been prepared by subcommittee 34A: Lamps, of IEC
technical committee 34: Lamps and related equipment.
The text of this standard is based on the following documents:
FDIS Report on voting
34A/1526/FDIS 34A/1555/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
---------------------- Page: 9 ----------------------
SIST EN 62639:2012
– 4 – 62639 IEC:2012
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
---------------------- Page: 10 ----------------------
SIST EN 62639:2012
62639 IEC:2012 – 5 –
INTRODUCTION
Performance standard IEC 62639 follows IEC 62532:2011-01, which is the safety standard for
induction lamps.
Requirements are given on marking, dimensions, starting characteristics, electrical
characteristics, photometric characteristics, lumen maintenance and life. Further, information
is given for designing ballasts and luminaires.
The requirements are detailed by means of lamp data sheets, diagrammatic data sheets and
maximum lamp outline sheets.
---------------------- Page: 11 ----------------------
SIST EN 62639:2012
– 6 – 62639 IEC:2012
FLUORESCENT INDUCTION LAMPS –
PERFORMANCE SPECIFICATION
1 Scope
This International Standard specifies the performance requirements for fluorescent induction
lamps for general lighting purposes.
In this standard, the term “lamp” stands for “induction lamp”.
It may be expected that lamps which comply with this standard will start and operate
satisfactorily at voltages between 92 % and 106 % of rated supply voltage and at an ambient
air temperature between 10 °C and 50 °C, when operated with ballasts complying with
IEC 60929 and IEC 61347-2-3, as far as applicable, and in a luminaire complying with
IEC 60598-1.
NOTE For some lamps, additional information for ballast design is given for proper starting at an ambient air
temperature of –15 °C.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60081:1997, Double-capped fluorescent lamps – Performance specifications
IEC 60598-1, Luminaires – Part 1: General requirements and tests
IEC 60929, AC and/or DC-supplied electronic control gear for tubular fluorescent lamps –
Performance requirements
IEC 61347-2-3, Lamp control gear – Part 2-3: Particular requirements for a.c. and/or d.c.
supplied electronic control gear for fluorescent lamps
IEC 62532:2011, Fluorescent induction lamps – Safety specifications
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 62532 and
IEC 60081 apply, together with the following.
3.1
ambient temperature
T
amb
average temperature of air or another medium in the vicinity of the lamp
---------------------- Page: 12 ----------------------
SIST EN 62639:2012
62639 IEC:2012 – 7 –
3.2
stabilization period
time required after switching on a lamp to reach stable values of luminous flux or lamp voltage
Note 1 to entry: Requirements on luminous flux are given in 4.6 and on tolerance of luminous flux in Clause B.2.
3.3
reference ballast
special electronic ballast, which is specified by the design specification of manufacturer
It is designed for the purpose of providing comparison standards for use in testing ballasts, for
the selection of reference lamps or for testing regular production lamps under standardized
conditions. It is essentially characterized by the fact that, at its rated frequency, it has a stable
voltage/current ratio which is relatively uninfluenced by variations in current, temperature and
magnetic surroundings, as outlined in the relevant ballast standard.
[SOURCE: IEC 60050-845:1987, 845-08-36, modified]
3.4
life
time during which a lamp is operated until its failure
Note 1 to entry: Switch-off times are not regarded when calculating life.
3.5
nominal life
life (in hours) as declared by the manufacturer
It is published together with the switching cycle and failure rate on which it is based.
Note 1 to entry: Example for a short version: 12B10 (12 h switching cycle / 10 % failures).
4 Lamp requirements
4.1 General
A lamp, on which compliance with this standard is claimed, shall comply with the requirements
of IEC 62532.
A lamp has to comply with further requirements or more stringent requirements, if they
published by manufacturer.
A lamp shall be so designed that its performance is reliable in normal and accepted use. In
general, this can be achieved by satisfying the requirements of the following subclauses.
The requirements and information given apply to 95 % of production.
NOTE The requirements and tolerances permitted by this standard correspond to the testing of a type test
sample, submitted by the manufacturer for that purpose. In principle, this type test sample should consist of units
having characteristics typical of the manufacturer’s production and being as close to the production centre point
values as possible.
It may be expected with the tolerances given in the standard that products manufactures in accordance with the
type test sample will comply with the standard of the majority of production. Due to the production spread however,
it is inevitable that there will sometimes be products outside the specified tolerances.
Measurements are carried out under reference conditions with values specified on the data
sheets, if available. Except where otherwise specified in the annexes, lamps shall be tested in
an ambient temperature of between 20 °C and 27 °C.
---------------------- Page: 13 ----------------------
SIST EN 62639:2012
– 8 – 62639 IEC:2012
4.2 Marking
4.2.1 General
In addition to the marking requirements of IEC 62532, the following is specified.
4.2.2 Correlated colour temperature (CCT) and colour rendering index (R )
a
The value of the correlated colour temperature and colour rendering index shall be provided
on the lamp itself or on the packaging (under consideration). The value representing CCT and
R may take the form as given in the International Lamp Coding System (ILCOS).
a
NOTE An R of 80 and a CCT of 3 000 K may be combined in the abbreviation “830”.
a
4.2.3 Polarity
The polarity shall be identified by marking the terminals (+, -). Other means of identifying are
possible instead, see Clause B.2.
4.3 Dimensions
The dimensions of a lamp shall comply with the values specified on the relevant lamp data
sheet.
Compliance: By measuring with callipers or equivalent.
4.4 Starting characteristics
A lamp shall start fully within the time specified on the relevant lamp data sheet and remain
alight.
Compliance: Visual inspection to verify that lamps are starting and remain alight. If the lamp
has achieved breakdown at ≤U and stayed alight, it has passed the test.
min
Conditions and method of test are given in Annex A.
4.5 Electrical characteristics
Requirements for lamp voltage and power are given below.
a) The initial reading of the voltage at the lamp terminals shall comply with the values
specified on the relevant lamp data sheet.
b) The initial reading of the power dissipated by a lamp shall not exceed the rated power
specified on the relevant lamp data sheet by more than 5 %.
Conditions and method of test are given in Annex B.
4.6 Photometric characteristics
Requirements for luminous flux, chromaticity coordinates and colour rendering index are
given below.
a) The initial reading of the luminous flux of a lamp shall be not less than 90 % and the
average of a batch shall be not less than 95 % (under consideration) of the declared
value.
b) If specified, the initial reading of the chromaticity co-ordinates x and y of a lamp shall be
within 5 SDCM (standard deviation of colour matching) from the rated values.
c) The initial reading of the general colour rendering index R of a lamp shall be not less
a
than the rated value decreased by three.
---------------------- Page: 14 ----------------------
SIST EN 62639:2012
62639 IEC:2012 – 9 –
Conditions and method of test are given in Annex B.
4.7 Lumen maintenance
The lumen maintenance of a lamp, at any time in its life, shall be not less than 90 % of the
rated lumen maintenance value.
Conditions and method of test are given in Annex C.
4.8 Life
Requirements are provided by the lamp manufacturer.
5 Information for ballast design
Refer to the relevant lamp data sheet and to Annex D for information for ballast design.
6 Information for luminaire design
Refer to the relevant lamp data sheet and to Annex E for information for luminaire design. The
regional requirements on EMC should be regarded.
7 Data sheets
7.1 Diagrammatic data sheets for location of lamp dimensions
62639-IEC-01 rectangular shaped lamps
62639-IEC-02 circular shaped lamps
62639-IEC-03 A110, A130 and A140 shaped lamps
62639-IEC-04 G95 shaped lamps
62639-IEC-05 PS110 shaped lamps
62639-IEC-06 PS180 shaped lamps
62639-IEC-07 R160 shaped lamps
62639-IEC-08 T85 shaped lamps
---------------------- Page: 15 ----------------------
SIST EN 62639:2012
– 10 – 62639 IEC:2012
INDUCTION LAMPS
DIAGRAMMATIC DATA SHEET FOR LOCATION OF
LAMP DIMENSIONS
Rectangular shaped, externally coupled, a-type
These drawings are intended only to indicate dimensions to be controlled
and are to be used in conjunction with the relevant lamp standard sheets.
L L S
4 3
W
L
5
L
1
L
2
D
H
2
H
1
Texte français au
62639-IEC-01-1
verso
French text overleaf
---------------------- Page: 16 ----------------------
SIST EN 62639:2012
62639 IEC:2012 – 11 –
INDUCTION LAMPS
DIAGRAMMATIC DATA SHEET FOR LOCATION OF
LAMP DIMENSIONS
Circular shaped, externally coupled, b-type
These drawings are intended only to indicate dimensions to be controlled
and are to be used in conjunction with the relevant lamp standard sheets.
W
H
L L
Texte français au
62639-IEC-02-1
verso
French text overleaf
---------------------- Page: 17 ----------------------
SIST EN 62639:2012
– 12 – 62639 IEC:2012
INDUCTION LAMPS
DIAGRAMMATIC DATA SHEET FOR LOCATION OF
LAMP DIMENSIONS
A110, A130 and A140 shaped, internally coupled, a-type
These drawings are intended only to indicate dimensions to be controlled
and are to be used in conjunction with the relevant lamp standard sheets.
D
L
B
Texte français au
62639-IEC-03-1
verso
French text overleaf
---------------------- Page: 18 ----------------------
SIST EN 62639:2012
62639 IEC:2012 – 13 –
INDUCTION LAMPS
DIAGRAMMATIC DATA SHEET FOR LOCATION OF
LAMP DIMENSIONS
G95 shaped, internally coupled, b-type
These drawings are intended only to indicate dimensions to be controlled
and are to be used in conjunction with the relevant lamp standard sheets.
D
L
B
Texte français au
62639-IEC-04-1
verso
French text overleaf
---------------------- Page: 19 ----------------------
SIST EN 62639:2012
– 14 – 62639 IEC:2012
INDUCTION LAMPS
DIAGRAMMATIC DATA SHEET FOR LOCATION OF
LAMP DIMENSIONS
PS110 shaped, internally coupled, b-type
These drawings are intended only to indicate dimensions to be controlled
and are to be used in conjunction with the relevant lamp standard sheets.
D
L
B
Texte français au
62639-IEC-05-1
verso
French text overleaf
---------------------- Page: 20 ----------------------
SIST EN 62639:2012
62639 IEC:2012 – 15 –
INDUCTION LAMPS
DIAGRAMMATIC DATA SHEET FOR LOCATION OF
LAMP DIMENSIONS
PS180 shaped, internally coupled, b-type
These drawings are intended only to indicate dimensions to be controlled
and are to be used in conjunction with the relevant lamp standard sheets.
D
L
B
Texte français au
62639-IEC-06-1
verso
French text overleaf
---------------------- Page: 21 ----------------------
SIST EN 62639:2012
– 16 – 62639 IEC:2012
INDUCTION LAMPS
DIAGRAMMATIC DATA SHEET FOR LOCATION OF
LAMP DIMENSIONS
R160 shaped, internally coupled, b-type
These drawings are intended only to indicate dimensions to be controlled
and are to be used in conjunction with the relevant lamp standard sheets.
D
L
B
Texte français au
62639-IEC-07-1
verso
French text overleaf
---------------------- Page: 22 ----------------------
SIST EN 62639:2012
62639 IEC:2012 – 17 –
INDUCTION LAMPS
DIAGRAMMATIC DATA SHEET FOR LOCATION OF
LAMP DIMENSIONS
T85 shaped, internally coupled, a-type
These drawings are intended only to indicate dimensions to be controlled
and are to be used in conjunction with the relevant lamp standard sheets.
D
L
B
Texte français au
62639-IEC-08-1
verso
French text overleaf
---------------------- Page: 23 ----------------------
SIST EN 62639:2012
– 18 – 62639 IEC:2012
7.2 Lamp data sheets
Lamp data sheets are in the order:
1) Shape: (a) round, elliptical, parabolic; (b) rectangular; (c) circular
2) Power, starting with the lowest power
Sheet-No Power Frequency Shape Energetic
coupling
62639-IEC-
Lamp System
rated nominal
W kHz
0035 30 35 135 G95 Internally b-type
0040 36 40 2 650 T85 Internally a-type
0050 50 55 135 PS110 Internally b-type
0055 47 55 2 650 T85 Internally a-type
0070 63 70 2 650 A110 Internally a-type
0085 78 85 2 650 A110 Internally a-type
0100 90 100 2 650 A130 Internally a-type
0150 135 150 2 650 A140 Internally a-type
0160 150 165 135 R160 Internally b-type
0165 150 165 2 650 A130 Internally a-type
0200 180 200 250 A140 Internally a-type
0260 240 260 135 PS180 Internally b-type
1070 70 250 rectangular Externally a-type
1075 75 250 rectangular Externally a-type
1080 80 230 rectangular Externally a-type
1100 100 250 rectangular Externally a-type
1105 100 230 rectangular Externally a-type
1120 120 230 rectangular Externally a-type
1150 150 250 rectangular Externally a-type
1200 200 230 rectangular Externally a-type
2080 80 230 circular Externally b-type
2100 100 230 circular Externally b-type
2120 120 230 circular Externally b-type
2150 150 250 circular Externally b-type
2200 200 250 circular Externally b-type
---------------------- Page: 24 ----------------------
SIST EN 62639:2012
62639 IEC:2012 – 19 –
INDUCTION LAMP
DATA SHEET Page 1
Internally b-type
ILCOS: FSGI-30-95/207
Nominal system power W 35
Bulb shape G95
Dimensions (mm)
L (height) D (diameter) B (diameter lampbase)
207 95 80
Lamp electrical characteristics
Frequency Rated power Rated voltage Star
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.