EN 13418:2004+A1:2008
(Main)Plastics and rubber machines - Winding machines for film or sheet - Safety requirements
Plastics and rubber machines - Winding machines for film or sheet - Safety requirements
This European Standard specifies the safety requirements for the design and construction of winding, unwinding and rewinding machines for film or sheet manufactured from rubber, plastics and composite materials in respect of the significant hazards listed in clause 4.
A winding machine begins at the intake of the film or sheet into the winding machine and ends at the discharge position of the reel(s).
An unwinding machine begins at the take-up position of the reel(s) and ends at the film or sheet take-off point.
A rewinding machine begins at the take-up position of the reel(s) and ends at the discharge position of the reel(s).
In some machines the winding, unwinding and rewinding functions may be combined.
The following functional groups are covered by this European Standard:
- fixed point roll;
- film or sheet tension control;
- winding zone;
- reel change device;
- reel loading and unloading devices;
and the following additional equipment integrated into the winding machine:
- spreader roll device;
- longitudinal cutting unit;
- slitting device;
- film or sheet alignment device;
- static eliminator.
Technical safety requirements for the design and construction of aids for lifting and handling, e.g. of winding cores or reels, are not covered by this standard.
Technical safety requirements for the design and construction of thickness monitoring devices are not covered by this standard.
Hazards due to electro-magnetic radiation, e.g. from the use of thickness monitoring devices, are not covered by this standard.
Toxic or chemical hazards and hazards due to dusts, fumes or gases, which could occur from the materials being wound are not covered by this standard.
NOTE Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this European Standard. The present standard is not intended to provide means of complying with the essen
Kunststoff- und Gummimaschinen - Wickelmaschinen für flache Bahnen - Sicherheitsanforderungen
Dieses Dokument legt die sicherheitstechnischen Anforderungen für Konzipierung und Bau von Maschinen zum Aufwickeln, Abwickeln und Umwickeln von flachen Bahnen aus Gummi, Kunststoffen und Verbund-materialien bezüglich der in Abschnitt 4 aufgelisteten signifikanten Gefährdungen fest.
Eine Wickelmaschine zum Aufwickeln beginnt am Flachbahneinlauf in die Wickelmaschine und endet an der Entnahmestelle der Rolle(n).
Eine Wickelmaschine zum Abwickeln beginnt an der Aufnahmestelle der Rolle(n) und endet am Flachbahn-auslauf.
Eine Wickelmaschine zum Umwickeln beginnt an der Aufnahmestelle der Rolle(n) und endet an der Entnahmestelle der Rolle(n).
Bei einigen Maschinen können die Aufwickel-, Abwickel- und Umwickelfunktionen kombiniert sein.
Die folgenden Funktionsgruppen sind in dieser Europäischen Norm behandelt:
- Festpunktwalze;
- Bahnzugkontrolle;
- Wickelstellenbereich;
- Rollenwechseleinrichtung;
- Rollenbeschickungs- und -entnahmeeinrichtung;
und folgende in der Wickelmaschine integrierte Zusatzeinrichtungen:
- Breithalteeinrichtung;
- Längstrenneinrichtung;
- Schlitzeinrichtung;
- Bahnsteuerung;
- Einrichtung zum Abbau elektrostatischer Aufladung.
Sicherheitstechnische Anforderungen für Konzipierung und Bau von Hilfen für das Heben und Handhaben, von z. B. Wickelkernen und -rollen, werden in dieser Norm nicht behandelt.
Sicherheitstechnische Anforderungen für Konzipierung und Bau von Dickenmesseinrichtungen werden in dieser Norm nicht behandelt.
Gefährdungen durch elektromagnetische Strahlung, z. B. durch die Verwendung von Dickenmess-einrichtungen, werden in dieser Norm nicht behandelt.
Toxische oder chemische Gefährdungen und Gefährdungen durch Stäube, Dämpfe oder Gase, die durch die zu wickelnden Materialien auftreten könnten, werden in dieser Norm nicht behandelt.
(...)
Machines pour les matières plastiques et le caoutchouc - Bobineuses pour films ou feuilles - Prescriptions de sécurité
Stroji za predelavo gume in plastike - Navijalniki za folije (filme) in trakove - Varnostne zahteve
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stroji za predelavo gume in plastike - Navijalniki za folije (filme) in trakove - Varnostne zahteveKunststoff- und Gummimaschinen - Wickelmaschinen für flache Bahnen - SicherheitsanforderungenMachines pour les matières plastiques et le caoutchouc - Bobineuses pour films ou feuilles - Prescriptions de sécuritéPlastics and rubber machines - Winding machines for film or sheet - Safety requirements83.200Oprema za gumarsko industrijo in industrijo polimernih materialovEquipment for the rubber and plastics industriesICS:Ta slovenski standard je istoveten z:EN 13418:2004+A1:2008SIST EN 13418:2004+A1:2008en01-december-2008SIST EN 13418:2004+A1:2008SLOVENSKI
STANDARD
SIST EN 13418:2004+A1:2008
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13418:2004+A1
October 2008 ICS 83.200 Supersedes EN 13418:2004English Version
Plastics and rubber machines - Winding machines for film or sheet - Safety requirements
Machines pour les matières plastiques et le caoutchouc - Bobineuses pour films ou feuilles - Prescriptions de sécurité
Kunststoff- und Gummimaschinen - Wickelmaschinen für flache Bahnen - Sicherheitsanforderungen This European Standard was approved by CEN on 2 February 2004 and includes Amendment 1 approved by CEN on 15 June 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13418:2004+A1:2008: ESIST EN 13418:2004+A1:2008
EN 13418:2004+A1:2008 (E)
2 Contents Page Foreword.4 Introduction.5 1 Scope.5 2 Normative references.6 3 Definitions.8 4 List of significant hazards.11 4.1 Mechanical hazards.11 4.2 Hazards resulting from electrical energy.13 4.3 Hazards resulting from unfavourable posture or excess efforts.13 4.4 Hazards resulting from noise.13 4.5 Hazards caused by failure of energy supply.13 4.6 Hazards resulting from failure of control systems.13 4.7 Hazards caused by setting up and maintenance of cutting devices.13 5 Safety requirements and/or protective measures.13 5.1 General safety requirements and/or protective measures.13 5.1.1 Protection of danger points/areas.13 5.1.2 Safety distances to prevent danger points/areas being reached.14 5.1.3 Minimum distances to avoid crushing of parts of the human body.14 5.1.4 Drive
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.