EN 50307:2002
(Main)Lead and lead alloys - Lead and lead alloy sheaths and sleeves of electric cables
Lead and lead alloys - Lead and lead alloy sheaths and sleeves of electric cables
This European Standard specifies the designations, chemical compositions and other requirements for lead and lead alloy electric cable sheaths and sleeves.
Blei und Bleilegierungen - Mäntel und Metallgehäuse von Kabeln aus Blei und Bleilegierungen
Plomb et alliages de plomb - Gaines et manchons en plomb et alliage de plomb des câbles électriques
Lead and lead alloys - Lead and lead alloy sheaths and sleeves of electric cables
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 50307:2004
01-januar-2004
Lead and lead alloys - Lead and lead alloy sheaths and sleeves of electric cables
Lead and lead alloys - Lead and lead alloy sheaths and sleeves of electric cables
Blei und Bleilegierungen - Mäntel und Metallgehäuse von Kabeln aus Blei und
Bleilegierungen
Plomb et alliages de plomb - Gaines et manchons en plomb et alliage de plomb des
câbles électriques
Ta slovenski standard je istoveten z: EN 50307:2002
ICS:
29.060.20 Kabli Cables
77.150.60 6YLQþHQLFLQNRYLLQNRVLWURYL Lead, zinc and tin products
L]GHONL
SIST EN 50307:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 50307:2004
---------------------- Page: 2 ----------------------
SIST EN 50307:2004
EUROPEAN STANDARD EN 50307
NORME EUROPÉENNE
EUROPÄISCHE NORM December 2002
ICS 77.150.60
English version
Lead and lead alloys –
Lead and lead alloy sheaths and sleeves
of electric cables
Plomb et alliages de plomb – Blei und Bleilegierungen –
Gaines et manchons en plomb et alliage Mäntel und Metallgehäuse von Kabeln
de plomb des câbles électriques aus Blei und Bleilegierungen
This European Standard was approved by CENELEC on 2002-10-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2002 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 50307:2002 E
---------------------- Page: 3 ----------------------
SIST EN 50307:2004
EN 50307:2002 - 2 -
Foreword
This European Standard was prepared by the Technical Committee CENELEC TC 20, Electric
cables.
The text of the draft was submitted to the formal vote and was approved by CENELEC as
EN 50307 on 2002-10-01.
The following dates were fixed:
- latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2003-10-01
- latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2005-10-01
Users of this European Standard should note that it covers the chemical composition of lead
and lead alloy cable sheaths or sleeves after application or forming. CEN has issued a
European Standard (EN 12548) to cover lead and lead alloy ingots for use in the manufacture
of cable sheaths or sleeves. The compositional requirements therein apply to the material prior
to manufacture of the cable sheaths or sleeves and melting loss of some of the alloying
elements may occur during processing.
Annexes designated "normative" are part of the body of the standard.
Annexes designated "informative" are given for information only.
In this standard, Annex A and Annex B are informative.
__________
---------------------- Page: 4 ----------------------
SIST EN 50307:2004
- 3 - EN 50307:2002
Contents
1 Scope. 4
2 Normative references. 4
3 Definitions . 4
4 Designation . 4
5 Ordering information for sheaths and sleeves. 4
6 Requirements. 5
7 Sampling.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.