SIST EN ISO 407:2023

Small medical gas cylinders - Pin-index yoke-type valve connections (ISO 407:2023)

This document is applicable to pin-index yoke-type valve connections for medical gas cylinders, with a working pressure up to a maximum of 200 bar or test pressure up to a maximum of 300 bar, or both.
NOTE 1    This type of connection is primarily used for small cylinders (5 l or below).
NOTE 2    In this document the unit bar is used, due to its universal use in the field of technical gases. It should, however, be noted that bar is not an SI unit, and that the corresponding SI unit for pressure is Pa (1 bar = 105 Pa = 105 N/m2).
This document specifies:
—    basic dimensions;
—    requirements for alternative designs of the yoke-type valve connections;
—    dimensions and positions for the holes and pins for the outlet connections.
It also specifies the dimensions and positions for the holes and pins for the outlet connections for gases and gas mixtures.

Kleine Gasflaschen für die medizinische Anwendung - Ventilseitenstutzen mit Anschlussbügel nach dem PIN-Index-System (ISO 407:2023)

Dieses Dokument gilt für Bügelverschlüsse nach dem Pin-Index-System für Gasflaschen für die medizinische Anwendung mit einem maximalen Arbeitsdruck bis 200 bar oder einem maximalen Prüfdruck bis 300 bar oder beidem.
ANMERKUNG 1   Diese Verbindungsart wird hauptsächlich an kleinen Gasflaschen (5 l oder weniger) angewendet.
ANMERKUNG 2   In diesem Dokument wird die Einheit Bar verwendet, da sie im Bereich der technischen Gase universell einsetzbar ist. Es sollte jedoch beachtet werden, dass das Bar keine SI-Einheit ist und dass die entsprechende SI Einheit für den Druck Pa ist (1 bar = 105 Pa = 105 N/m2).
Dieses Dokument legt Folgendes fest:
   Grundmaße;
   Anforderungen an alternative Auslegungen von Bügelventilverschlüssen;
   Maße und Anordnungen der Passlöcher und -stifte für die Anschlussverbindungen.
Es legt auch die Maße und Anordnungen der Passlöcher und -stifte für die Anschlussverbindungen für Gase und Gasgemische fest.

Petites bouteilles à gaz médicaux - Raccords de robinets du type étrier avec ergots de sécurité (ISO 407:2023)

Le présent document s’applique aux raccords de robinet du type étrier avec ergots de sécurité pour bouteilles à gaz médicaux d’une pression de service maximale de 200 bar et/ou d’une pression d’épreuve maximale de 300 bar.
NOTE 1        Ce type de raccord est essentiellement utilisé pour les petites bouteilles (de 5 l ou moins).
NOTE 2        Dans ce document, l’unité de pression utilisée est le bar, en raison de son usage universel dans le domaine des gaz techniques. Il convient cependant de noter que le bar n’est pas une unité du Système international, lequel utilise le Pascal (Pa) (1 bar = 105 Pa = 105 N/m2) pour la pression.
Le présent document spécifie:
—    les dimensions de base des raccords;
—    les exigences requises des variantes de construction des raccords de robinets du type étrier;
—    les dimensions et positions des trous et des ergots des raccords de sortie.
Il spécifie également les dimensions et les positions des trous et des ergots des sorties de raccords pour les gaz et les mélanges de gaz.

Male plinske jeklenke za uporabo v medicini - Ventilski priključni nastavki po sistemu pin-index (ISO 407:2023)

Ta dokument se uporablja za ventilske priključne nastavke po sistemu pin-index za plinske jeklenke za uporabo v medicini z delovnim tlakom do največ 200 bar ali preskusnim tlakom do največ 300 bar oziroma obojim.
OPOMBA 1: Ta vrsta priključka se uporablja predvsem za male jeklenke (5 l ali manjše).
OPOMBA 2: V tem dokumentu je zaradi splošne uporabe na področju tehničnih plinov uporabljena enota bar. Vendar naj se upošteva, da bar ni enota SI in da je ustrezna enota SI za tlak Pa (1 bar = 105 Pa = 105 N/m2).
Ta dokument določa:
– osnovne mere;
– zahteve za alternativne zasnove ventilskih priključnih nastavkov po sistemu pin-index;
– mere in položaje lukenj in zatičev za izhodne priključke.
Določa tudi mere in položaje lukenj in zatičev za izhodne priključke plinov in njihovih zmesi.

General Information

• Status: Published
• Public Enquiry End Date: 24-May-2023
• Publication Date: 20-Aug-2023
• ICS: 11.040.10 - Anaesthetic, respiratory and reanimation equipment
• ICS: 23.020.35 - Gas cylinders
• ICS: 23.060.40 - Pressure regulators
• Technical Committee: TLP - Pressure vessels
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 10-Aug-2023
• Due Date: 15-Oct-2023
• Completion Date: 21-Aug-2023
• Ref Project: EN ISO 407:2023 - Small medical gas cylinders - Pin-index yoke-type valve connections (ISO 407:2023)

Relations

• Replaces: SIST EN ISO 407:2021 - Small medical gas cylinders - Pin-index yoke-type valve connections (ISO 407:2021)
• Effective Date: 01-Sep-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 407:2023
01-september-2023
Male plinske jeklenke za uporabo v medicini - Ventilski priključni nastavki po
sistemu pin-index (ISO 407:2023)
Small medical gas cylinders - Pin-index yoke-type valve connections (ISO 407:2023)
Kleine Gasflaschen für die medizinische Anwendung - Ventilseitenstutzen mit
Anschlussbügel nach dem PIN-Index-System (ISO 407:2023)
Petites bouteilles à gaz médicaux - Raccords de robinets du type étrier avec ergots de
sécurité (ISO 407:2023)
Ta slovenski standard je istoveten z: EN ISO 407:2023
ICS:
11.040.10 Anestezijska, respiratorna in Anaesthetic, respiratory and
reanimacijska oprema reanimation equipment
23.020.35 Plinske jeklenke Gas cylinders
23.060.40 Tlačni regulatorji Pressure regulators
SIST EN ISO 407:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 407:2023

---------------------- Page: 2 ----------------------
SIST EN ISO 407:2023


EN ISO 407
EUROPEAN STANDARD

NORME EUROPÉENNE

August 2023
EUROPÄISCHE NORM
ICS 11.040.10 Supersedes EN ISO 407:2021
English Version

Small medical gas cylinders - Pin-index yoke-type valve
connections (ISO 407:2023)
Petites bouteilles à gaz médicaux - Raccords de Kleine Gasflaschen für die medizinische Anwendung -
robinets du type étrier avec ergots de sécurité (ISO Ventilseitenstutzen mit Anschlussbügel nach dem PIN-
407:2023) Index-System (ISO 407:2023)
This European Standard was approved by CEN on 1 July 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 407:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 407:2023
EN ISO 407:2023 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 407:2023
EN ISO 407:2023 (E)
European foreword
This document (EN ISO 407:2023) has been prepared by Technical Committee ISO/TC 58 "Gas
cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2024, and conflicting national standards
shall be withdrawn at the latest by February 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 407:2021.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 407:2023 has been approved by CEN as EN ISO 407:2023 without any modification.

3

-------------
...

SLOVENSKI STANDARD
oSIST prEN ISO 407:2023
01-maj-2023
Male plinske jeklenke za uporabo v medicini - Ventilski priključni nastavki po
sistemu pin-index (ISO/FDIS 407:2023)
Small medical gas cylinders - Pin-index yoke-type valve connections (ISO/FDIS
407:2023)
Kleine Gasflaschen für die medizinische Anwendung - Ventilseitenstutzen mit
Anschlussbügel nach dem PIN-Index-System (ISO/FDIS 407:2023)
Petites bouteilles à gaz médicaux - Raccords de robinets du type étrier avec ergots de
sécurité (ISO/FDIS 407:2023)
Ta slovenski standard je istoveten z: prEN ISO 407
ICS:
11.040.10 Anestezijska, respiratorna in Anaesthetic, respiratory and
reanimacijska oprema reanimation equipment
23.020.35 Plinske jeklenke Gas cylinders
23.060.40 Tlačni regulatorji Pressure regulators
oSIST prEN ISO 407:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 407:2023

---------------------- Page: 2 ----------------------
oSIST prEN ISO 407:2023
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 407
ISO/TC 58/SC 2
Small medical gas cylinders — Pin-
Secretariat: AFNOR
index yoke-type valve connections
Voting begins on:
2023-03-08
Petites bouteilles à gaz médicaux — Raccords de robinets du type
étrier avec ergots de sécurité
Voting terminates on:
2023-05-31
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 407:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 3 ----------------------
oSIST prEN ISO 407:2023
ISO/FDIS 407:2023(E)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 407
ISO/TC 58/SC 2
Small medical gas cylinders — Pin-
Secretariat: AFNOR
index yoke-type valve connections
Voting begins on:
Petites bouteilles à gaz médicaux — Raccords de robinets du type
étrier avec ergots de sécurité
Voting terminates on:
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
ISO/CEN PARALLEL PROCESSING
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: [phone]
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: [e-mail]
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/FDIS 407:2023(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN­
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
  © ISO 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 4 ----------------------
oSIST prEN ISO 407:2023
ISO/FDIS 407:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Valve . 1
5 Yoke .
...