55.180.01 - Freight distribution of goods in general

This document establishes requirements for transport and condition monitoring of transported consignments such as agri-food and perishable goods, through applications, models, processes, and information bundles. This document applies to both domestic and cross-border transport of transported consignments, and incorporates the methods described in ISO/IEC 19845, ISO/TS 24533 and ISO/TS 17187 which are transport domain specific, as discussed in the Introduction. Specific extensions include additio...view more

This European Standard specifies the technical and functional properties of automatic recording equipment used to determine randomly appearing shocks during transportation.
Such automatic recording equipment can be used to:
-   determine mechanical shock loads on individual transportations;
-   monitor the transportation means to observe the limits of the shock parameters;
-   determine the shock loads on the transported item.
This standard defines the sensors to be attached to the device, and specifi...view more

This European Standard specifies the technical and functional properties of automatic recording equipment used to determine randomly appearing shocks during transportation.
Such automatic recording equipment can be used to:
—   determine mechanical shock loads on individual transportations;
—   monitor the transportation means to observe the limits of the shock parameters;
—   determine the shock loads on the transported item.
This standard defines the sensors to be attached to the device, and sp...view more

This European Standard defines principles to be considered when transporting objects.
It should be used in accordance with EN 15946 "Conservation of cultural property – Packing principles for transport".

This European Standard specifies the technical requirements to minimise the hazards listed in Clause 4 which can arise during the commissioning, the operation and the maintenance of container/pallet loaders when used as intended, including misuse reasonably foreseeable by the manufacturer, when carried out in accordance with the specifications given by the manufacturer or his authorised representative. It also takes into account some requirements recognised as essential by authorities, aircraft ...view more

This European Standard specifies the documentation of measurements for climatic and other loads (such as sunlight, sand, dust and electromagnetic radiation) during transport, handling and storage.

ISO 26683-1:2013 provides the context for application interface profiles for the exchange of land transport data using current technologies and existing standards for item identification, package identification, container identification, and international standards and practices regarding freight and its movement.

This European Standard specifies the documentation of measurements for climatic and other loads (such as sunlight, sand, dust and electromagnetic radiation) during transport, handling and storage.

ISO 26683-2:2013 provides application interface profiles for land cargo transport data agglomeration and transfer (within the context and architecture described in ISO 26683-1), using one or more of the international standards listed and defined in Annex A of 26683-1. ISO 26683-2:2013 defines a number of application interface profiles for land cargo transport data to provide more land cargo transport visibility by using current technical standards, specifications and technologies related to carg...view more

ISO/TS 24533:2012 specifies the data concepts applicable to the movement of freight and its intermodal transfer. These data concepts include information entities (data elements), aggregated/associated information entities (groups of data elements) and messages that comprise information exchanges at transport interfaces along the chain of participants responsible for the delivery of goods from the point of origin through to the final recipient. ISO/TS 24533 focuses on a single "thread" of the ove...view more

This European Standard specifies the technical requirements to minimise the hazards listed in Clause 4 which can arise during the commissioning, operation and maintenance of container/pallet transfer transporters when carried out in accordance with the specifications given by the manufacturer or his authorised representative. It also takes into account some performance requirements recognised as essential by authorities, aircraft and ground support equipment (GSE) manufacturers as well as airlin...view more

This part of this standard defines requirements to be observed during the measurement and analysis of dynamic-mechanical transportation loads, should the results raise a claim of generalisation and be incorporated in this series of standards as fundamental data.

This standard contains commitments for the preparation, performance and documentation of transportation measurements.  Of special advantage are the added normative annexes for particular transportation carriers, which will be supplemented in the future and which the user can copy for measuring purposes. The following measuring reports and log sheets are contained in this standard:
- Annex A:   Road transportation
- Annex B:   In-plant transportation (measurement on the transportation means)
- Ann...view more

When measuring and analysing dynamic processes, quite often unnoticed or difficult to recognise disturbances or erroneous measurements occur, which impair the application of these values.  This part therefore defines procedures which permit the assessment of the validity and to evaluate the measured results which have been acquired according to EN15433-2 in order to detect possible errors before any actual analysis occurs.

To simulate transportation loads, it is helpful to work with standardised load assumptions which base on the actual loads acquired according to EN 15433-2 up to EN 15433-4. The derivation of test specifications bases fundamentally on considerations concerning the reproduction of damages, whereby especially time compressed fatigue simulation has to be considered for the determination of the test intensity.

This standard presents guidelines for instruments, procedures and parameters, to analyse dynamic data.  It is assumed that the person performing the analyses disposes of appropriate digital FFT signal processors or FFT computers.
The guidelines are also applicable for other types of signal processing procedures, as long as the analysing parameters are equivalent.  Such other procedures contain correlation algorithms (i.e. "Blackman-Tuckey), digital band pass filter algorithms or heterodyne tec...view more

This standard presents guidelines for the instruments, procedures and parameters, used to analyse dynamic data.  It is assumed that the person performing the analyses has the use of appropriate digital FFT signal processors or FFT computers.
These guidelines are also applicable for other types of signal processing procedures, as long as the analysing parameters are equivalent. Such other procedures contain correlation algorithms e.g. Blackman-Tuckey), digital band pass filter algorithms or het...view more

This standard defines procedures for assessing the validity of results acquired in accordance with EN 15433-2, and for evaluating these results.
NOTE   When measuring and analysing dynamic processes, quite often unnoticed or difficult to recognize disturbances or erroneous measurements occur, which impair the application of these values. These procedures are necessary in order to detect possible errors before any actual analysis occurs.
Figure 1 provides an overview of the data validation and e...view more

This standard gives guidelines for the derivation of test specifications from data acquired according to EN 15433-2, EN 15433-3 and EN 15433-4.
NOTE   To simulate transportation loads, it is helpful to work with standardized load assumptions that are based on the actual loads acquired according to EN 15433-2 up to EN 15433-4. The derivation of test specifications is based fundamentally on considerations concerning the reproduction of damage, whereby time compressed fatigue simulation in particula...view more

This standard specifies the general requirements to be observed during the measurement and evaluation of dynamic-mechanical transportation loads, should the results raise a claim of generalization and be incorporated in this series of standards as fundamental data.