M/086 - Transport of dangerous goods

This document specifies requirements for two types of hose assemblies (Types D and SD) and four grades based on electrical properties with hoses made of rubber or thermoplastics and hose fittings made of metal designed to convey liquid or gaseous chemical substances, hereinafter termed the “chemicals conveyed”.
The hose assemblies are intended for use with chemicals conveyed in the temperature range of –20 °C to +65 °C at a working pressure ≤ 10 bar1).
NOTE 1 This document sets out requirement...view more

This European Standard specifies minimum requirements for materials, design, construction and workmanship procedures, and tests for welded LPG road tanker pressure vessels and their welded attachments manufactured from carbon, carbon/manganese and micro alloy steels.
There is no upper size limit as this is determined by the gross vehicle weight limitation.
This European Standard does not cover pressure vessels for pressure vessel containers.
NOTE 1   In the context of this standard the term "ro...view more

This European Standard specifies the design, testing and marking requirements for spring loaded pressure relief valves (PRV), for use in liquefied petroleum gas (LPG) cylinders.
These PRVs can be either an integral part of a cylinder valve (see EN ISO 14245 [3] and EN ISO 15995 [4]) or a separate device.
This European Standard does not exclude the use of other designs of pressure relief devices that provide a similar level of safety.

This document specifies requirements for the design and construction of metallic gravity-discharge tanks intended for the carriage of substances having a vapour pressure not exceeding 110 kPa (1,1 bar) (absolute pressure) at 50 °C.
NOTE 1   Gravity discharge tanks have no maximum working pressure. However, during operation, pressure in the shell may occur, for example due to flow restrictions in vapour recovery systems or opening pressures of breather devices. It is important that these operating...view more

This European Standard specifies minimum requirements for the materials, design, construction, prototype testing and routine manufacturing inspections of composite gas cylinders and tubes for compressed hydrogen. This standard applies only to fully wrapped composite cylinders with carbon fibres intended to be permanently mounted in a frame (e.g. bundle or trailer) with a test pressure of not less than 300 bar.
NOTE 1 This European Standard does not address the design, fitting and performance of...view more

This document provides requirements for the selection of safe combinations of metallic cylinder and
valve materials and cylinder gas content.
The compatibility data given is related to single gases and to gas mixtures.
Seamless metallic, welded metallic and composite gas cylinders and their valves, used to contain
compressed, liquefied and dissolved gases are considered.
NOTE In this document the term “cylinder” refers to transportable pressure receptacles, which also include
tubes and pre...view more

This European Standard specifies procedures for the periodic inspection and testing, of transportable refillable LPG cylinders with a water capacity from 0,5 l up to and including 150 l.
This European Standard is applicable to welded and brazed steel LPG cylinders with a specified minimum wall thickness designed according to EN 1442, EN 12807, EN 13322-1, or equivalent standard (e.g. national codes).
This European Standard is intended to be applied to cylinders complying with RID/ADR (includin...view more

This European Standard specifies procedures for periodic inspection and testing, for transportable refillable LPG cylinders with a water capacity from 0,5 l up to and including 150 l.
This European Standard is applicable to the following:
-   welded steel LPG cylinders manufactured to an alternative design and construction, see EN 14140 or equivalent standard;
-   welded aluminium LPG cylinders, see EN 13110 or equivalent standard;
-   composite LPG cylinders, see EN 14427 or equivalent standard;
...view more

EN-ISO 16106 gives guidance on the application of a quality management system in the manufacture, measuring and monitoring of design type approved dangerous goods packaging, intermediate bulk containers (IBCs) and large packaging.This document does not include guidance specific to other management systems, such as those for environmental management, occupational health and safety management, or financial management.$0$0It is applicable to an organization that) needs to demonstrate its ability to...view more

EN ISO 10297 specifies design, type testing and marking requirements for: a) cylinder valves intended to be fitted to refillable transportable gas cylinders; b) main valves (excluding ball valves) for cylinder bundles; c) cylinder valves or main valves with integrated pressure regulator (VIPR); which convey compressed, liquefied or dissolved gases. NOTE 1 Where there is no risk of ambiguity, cylinder valves, main valves and VIPR are addressed with the collective term “valves” within this Interna...view more

This document specifies the minimum requirements for the design and construction of metallic pressure tanks having a maximum working pressure exceeding 50 kPa (0,5 bar), for the transport of dangerous goods by road and rail and sea. This document includes requirements for openings, closures and structural equipment; it does not cover requirements of service equipment. For tanks for the transport of cryogenic liquids, EN 13530 1 and EN 13530 2 apply.
Design and construction of pressure tanks acc...view more

This document specifies the minimum requirements for the design and construction of metallic pressure tanks having a maximum working pressure exceeding 50 kPa (0,5 bar), for the transport of dangerous goods by road and rail and sea. This document includes requirements for openings, closures and structural equipment; it does not cover requirements of service equipment. For tanks for the transport of cryogenic liquids, EN 13530 1 and EN 13530 2 apply.
Design and construction of pressure tanks acc...view more

This document gives guidance on the application of a quality management system in the manufacture, measuring and monitoring of design type approved dangerous goods packaging, intermediate bulk containers (IBCs) and large packaging.
This document does not include guidance specific to other management systems, such as those for environmental management, occupational health and safety management, or financial management.
It is applicable to an organization that:
a) needs to demonstrate its abili...view more

This document specifies the following points regarding the minimum requirements for an overfill prevention system:
-   functions;
-   major components;
-   characteristics;
-   test methods.
This document is applicable to overfill prevention systems for liquid fuels having a flash point up to but not exceeding 100 °C, excluding liquefied petroleum gas (LPG).
NOTE   Vapour path detection is not part of this standard but can be provided as an option.

This Standard specifies the requirements for the design, construction, testing and initial inspection of a transportable cylinder bundle. It is applicable to cylinder bundles containing cylinders containing compressed gas, liquefied gas and mixtures thereof. It is also applicable to cylinder bundles for acetylene. Additional requirements for acetylene cylinder bundles containing acetylene in a solvent are provided in Annex B. This document does not, however, cover acetylene cylinder bundles with...view more

This Standard specifies the requirements for valve protection caps and valve guards used on cylinders for liquefied, dissolved or compressed gases. Valve protection caps and valve guards are some of the options available to protect cylinder valves, including valves with integral pressure regulators (VIPRs) during transport. This document is applicable to valve protection caps and valve guards which inherently provide the primary protection of a cylinder valve. It can also be used to test other e...view more

This European Standard specifies minimum requirements for material, design, construction and workmanship, testing and examination during the manufacture of transportable refillable welded aluminium liquefied petroleum gas (LPG) cylinders, having a water capacity from 0,5 litres up to and including 150 litres, exposed to ambient temperature.

This document specifies the requirements for valve protection caps and valve guards used on cylinders for liquefied, dissolved or compressed gases.
Valve protection caps and valve guards are some of the options available to protect cylinder valves, including valves with integral pressure regulators (VIPRs) during transport.
This document is applicable to valve protection caps and valve guards which inherently provide the primary protection of a cylinder valve. It can also be used to test other...view more

This document specifies the requirements for the design, construction, testing and initial inspection of a transportable cylinder bundle.
It is applicable to cylinder bundles containing cylinders containing compressed gas, liquefied gas and mixtures thereof. It is also applicable to cylinder bundles for acetylene. Additional requirements for acetylene cylinder bundles containing acetylene in a solvent are provided in Annex B. This document does not, however, cover acetylene cylinder bundles wit...view more

This document specifies the requirements for design, specification, type testing and production testing and inspection for dedicated LPG self-closing cylinder valves for use with and directly connected to transportable refillable LPG cylinders. It also includes requirements for associated equipment for vapour and liquid service. Bursting discs and/or fusible plugs are not covered in this document. Annex A identifies requirements for production testing and inspection. This document excludes other...view more

This document specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at time of manufacture for refillable seamless steel gas cylinders and tubes with water capacities up to and including 450 l. it is applicable to cylinders and tubes for compressed, liquefied and dissolved gases and for quenched and tempered steel cylinders and tubes with an actual tensile strength Rma ≥ 1 100 MPa. It is not applicable to cylinders...view more

This document specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at time of manufacture for refillable seamless steel gas cylinders and tubes with water capacities up to and including 450 l. It is applicable to cylinders and tubes for compressed, liquefied and dissolved gases and for quenched and tempered steel cylinders and tubes with a maximum actual tensile strength Rma of less than 1 100 MPa.

This document specifies the requirements for design, specification, type testing and production testing and inspection for dedicated LPG self-closing cylinder valves for use with and directly connected to transportable refillable LPG cylinders. It also includes requirements for associated equipment for vapour and liquid service. Bursting discs and/or fusible plugs are not covered in this document. Annex A identifies requirements for production testing and inspection. This document excludes other...view more

This document specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at the time of manufacture for refillable seamless steel gas cylinders and tubes with water capacities up to and including 450 l. It is applicable to cylinders and tubes for compressed, liquefied and dissolved gases and for normalized or normalized and tempered steel cylinders and tubes.

ISO 10462 specifies requirements for the periodic inspection of acetylene cylinders as required for the transport of dangerous goods and for maintenance in connection with periodic inspection. It applies to acetylene cylinders with and without solvent and with a maximum nominal water capacity of 150 l.

This Standard provides additional terms and definitions to those written in the European Agreement Concerning the International Carriage of Dangerous Goods by Road (ADR) or the Regulations concerning the International Carriage of Dangerous Goods by Rail (RID), appearing as Appendix C to the Convention concerning International Carriage by Rail (COTIF). This document forms part of series of documents prepared by CEN/TC 296 regarding the transport of dangerous goods. The series supports the proper ...view more

This European Standard specifies the minimum requirements for the design, construction and testing during manufacture of transportable refillable brazed steel Liquefied Petroleum Gas (LPG) cylinders, of water capacity from 0,5 l up to and including 15 l, exposed to ambient temperatures.
This European Standard applies only to cylinders having a circular cross-section without any longitudinal joint.

This document specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at time of manufacture for refillable seamless steel gas cylinders and tubes with water capacities up to and including 450 l.
It is applicable to cylinders and tubes for compressed, liquefied and dissolved gases and for quenched and tempered steel cylinders and tubes with a maximum actual tensile strength Rma of less than 1 100 MPa.

This document specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at the time of manufacture for refillable seamless steel gas cylinders and tubes with water capacities up to and including 450 l.
It is applicable to cylinders and tubes for compressed, liquefied and dissolved gases and for normalized or normalized and tempered steel cylinders and tubes.

This document specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at time of manufacture for refillable seamless steel gas cylinders and tubes with water capacities up to and including 450 l.
it is applicable to cylinders and tubes for compressed, liquefied and dissolved gases and for quenched and tempered steel cylinders and tubes with an actual tensile strength Rma ≥ 1 100 MPa.
It is not applicable to cylind...view more

This document specifies the requirements for design, specification, type testing and production testing and inspection of dedicated LPG manually operated cylinder valves for use with and directly connected to transportable refillable LPG cylinders.
It also includes requirements for associated equipment for vapour and liquid service. Bursting discs and/or fusible plugs are not covered in this document.
Annex B identifies requirements for production testing and inspection.
This document exclude...view more

This document specifies the requirements for design, specification, type testing and production testing and inspection for dedicated LPG self-closing cylinder valves for use with and directly connected to transportable refillable LPG cylinders.
It also includes requirements for associated equipment for vapour and liquid service. Bursting discs and/or fusible plugs are not covered in this document.
Annex A identifies requirements for production testing and inspection.
This document excludes ot...view more

ISO 10462 specifies requirements for the periodic inspection of acetylene cylinders as required for the transport of dangerous goods and for maintenance in connection with periodic inspection. It applies to acetylene cylinders with and without solvent and with a maximum nominal water capacity of 150 l.

This document provides additional terms and definitions to those written in the European Agreement Concerning the International Carriage of Dangerous Goods by Road (ADR) or the Regulations concerning the International Carriage of Dangerous Goods by Rail (RID), appearing as Appendix C to the Convention concerning International Carriage by Rail (COTIF).
This document forms part of series of documents prepared by CEN/TC 296 regarding the transport of dangerous goods. The series supports the proper...view more

This document specifies the minimum requirements for the design, construction and testing during manufacture of transportable refillable brazed steel Liquefied Petroleum Gas (LPG) cylinders, of water capacity from 0,5 l up to and including 15 l, exposed to ambient temperatures.
This document applies only to cylinders having a circular cross-section without any longitudinal joint.

This European Standard specifies the design, testing and inspection requirements for pressure relief valve isolating devices, valve manifolds, vent pipes and system assemblies which are, where necessary, used with pressure relief valves for use in static pressure vessels for Liquefied Petroleum Gas (LPG) service.
This European Standard addresses both prototype testing and production testing of isolating devices and PRV manifolds.
Pressure relief valves for LPG pressure vessels are specified in...view more

This document specifies the minimum requirements for the cleanliness of all surfaces of cryogenic vessels and associated accessories that are in contact with the cryogenic fluid at any expected operating conditions.
This document defines the acceptable level of surface and particle contamination to minimize the risk of malfunction of equipment and ensure safety against ignition when in contact with oxygen or oxidizing fluids (see EN ISO 10156).

This European Standard specifies requirements for:
a)   routine inspection, periodic inspection and requalification of fixed LPG storage pressure vessels of sizes greater than 13 m3, and associated fittings;
b)   marking pressure vessels and/or keeping records, as appropriate, as a result of routine inspection, periodic inspection and requalification.
This European Standard excludes refrigerated storage.

This European Standard specifies the design, testing and inspection requirements for pressure relief valve isolating devices, valve manifolds, vent pipes and system assemblies which are, where necessary, used with pressure relief valves for use in static pressure vessels for Liquefied Petroleum Gas (LPG) service.
This European Standard addresses both prototype testing and production testing of isolating devices and PRV manifolds.
Pressure relief valves for LPG pressure vessels are specified in...view more

This document specifies the minimum requirements for the cleanliness of all surfaces of cryogenic vessels and associated accessories that are in contact with the cryogenic fluid at any expected operating conditions.
This document defines the acceptable level of surface and particle contamination to minimize the risk of malfunction of equipment and ensure safety against ignition when in contact with oxygen or oxidizing fluids (see EN ISO 10156).

This document specifies requirements for:
a)   routine inspection, periodic inspection and requalification of fixed LPG pressure vessels of sizes greater than 13 m3, and associated fittings;
b)   marking pressure vessels and/or keeping records, as appropriate, as a result of routine inspection, periodic inspection and requalification.
This document excludes refrigerated storage.

This standard gives design, construction, type and production testing, and marking requirements for non insulated cryogenic flexible hose used for the transfer of cryogenic fluids within the following range of operating conditions : - working temperature: from - 270 °C to + 65 °C ; - maximum nominal pressure: 80 bar ; - nominal size (DN): from 10 to 100. End fittings for mounting of any couplings are within the scope of this standard, but the couplings are subject to other standards. It is inten...view more

ISO 21012:2018 specifies design, construction, type and production testing, and marking requirements for non-insulated cryogenic flexible hoses used for the transfer of cryogenic fluids within the following range of operating conditions:
- working temperature: from −270 °C to +65 °C;
- nominal size (DN): from 10 to 100.
End fittings for mounting of any couplings are within the scope of this document, but the couplings are subject to other standards.
ISO 21012:2018 is intended that the hose b...view more

This document specifies the requirements for periodic inspection and testing to verify the integrity of cylinders and tubes to be re-introduced into service for a further period of time.
This document is applicable to seamless steel and seamless aluminium-alloy transportable gas cylinders (single or those that comprise a bundle) intended for compressed and liquefied gases under pressure, of water capacity from 0,5 l up to 150 l and to seamless steel and seamless aluminium-alloy transportable ga...view more

This European Standard specifies the minimum requirements for the design and construction of metallic pressure tanks having a maximum working or test pressure exceeding 50 kPa (0,5 bar), for the transport of dangerous goods by road and rail and sea. This European Standard includes requirements for openings, closures and structural equipment; it does not cover requirements of service equipment. For tanks for the transport of cryogenic liquids, EN 13530-1 and EN 13530-2 apply.
NOTE 1   Design and c...view more

This document specifies stamp marking of transportable gas cylinders of volumes greater than 0,12 l
and up to or equal to 150 l and tubes of volumes up to or equal to 3 000 l, including:
— steel and aluminium-alloy gas cylinders;
— composite gas cylinders;
— acetylene cylinders;
— liquefied petroleum gas (LPG) cylinders (see Annex A); and
— small cylinders (see Annex B).
Unless noted by exception, the use of “cylinder” in this document refers to the above types of cylinders.
Non-refillab...view more

This European Standard covers the manhole cover assembly and specifies the performance requirements, dimensions and tests necessary to verify the compliance of the equipment to this standard.
The equipment specified by this standard is suitable for use with liquid petroleum products and other dangerous substances of Class 3 of ADR - European Agreement concerning the International Carriage of Dangerous Goods by Road - (flammable liquids) which have a vapour pressure not exceeding 110 kPa at 50 °...view more