IEC 60352-7:2020 is available as IEC 60352-7:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60352-7:2020 is applicable to spring clamp connections made with stripped wire without further preparation: - solid conductors of 0,32 mm to 3,7 mm nominal diameter (0,08 mm2 to 10 mm2 cross‑section), or - stranded conductors of 0,08 mm2 to 10 mm2 cross-section, or - flexible conductors of 0,08 m...view more

    • sale 10% off
    • Standard
      34 pages
      English language
    • e-Library read for
      1 day

IEC 62435-7:2020 on long-term storage applies to micro-electromechanical devices (MEMS) in long-term storage that can be used as part of obsolescence mitigation strategy. Long-term storage refers to a duration that may be more than 12 months for products scheduled for storage. Philosophy, good working practice, and general means to facilitate the successful long-term storage of electronic components are also addressed.

    • sale 10% off
    • Standard
      22 pages
      English language
    • e-Library read for
      1 day

This document describes basic, common minimum functional requirements and recommendations for an accessible and usable built environment, following the Design for All/Universal Design principles which will facilitate equitable and safe use for a wide range of users, including persons with disabilities.
The requirements and recommendations given in this document are applicable across the full spectrum of the built environment.
These functional accessibility and usability requirements and recomm...
view more

    • sale 10% off
    • Standard
      295 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      289 pages
      English language
    • e-Library read for
      1 day

IEC 60384-13:2020 specifies preferred ratings and characteristics, selects from IEC 60384-1:2016 the appropriate quality assessment procedures, tests and measuring methods, and gives general performance requirements for this type of capacitor. Test severities and requirements specified in detail specifications referring to this sectional specification are of an equal or higher performance level. Lower performance levels are not permitted. This part of IEC 60384 applies to fixed direct current ca...view more

    • sale 10% off
    • Standard
      36 pages
      English language
    • e-Library read for
      1 day

Standardisation Request M/543 requires the following: "Definition of parameters and methods relevant for assessing durability, upgradability and ability to repair, re-use and re-manufacture of products". Hence, this Technical Report "Definitions related to material efficiency" will constitute a collection of common terms used in deliverables prepared in accordance with M/543. The purpose of such a collection is to provide a single definition of key terms used in different deliverables from the C...view more

    • sale 10% off
    • Technical report
      16 pages
      English language
    • e-Library read for
      1 day

The standard defines the transfer of electronic documents between stakeholders in the insurance industry (for
example between insurer and intermediary).
The standard specifies:
 the semantic process for the transfer of documents (for example insurance policy, claim notification,
correspondence) that may be transferred as an attached file and
 a limited number of meta data describing the document (for example type of document, identification of
insurer, intermediary and client, policy num...
view more

    • sale 10% off
    • Standard
      65 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      58 pages
      English language
    • e-Library read for
      1 day

This part of IEC 60645 specifies a means of describing the physical characteristics, in terms of
electrical waveforms, of audiometric reference and test signals of short duration and methods
for their measurement.
The object of this document is to ensure that audiometric stimuli of short duration are specified
and measured in the same way and that the calibration of equipment using such signals is
carried out using defined methods.
This document does not describe the method of use of short...
view more

    • sale 10% off
    • Standard
      17 pages
      English language
    • e-Library read for
      1 day

This part of IEC 60603-7 covers 8-way, unshielded, free and fixed connectors and is intended
to specify the common dimensions (interface dimensions), mechanical, electrical and
environmental characteristics and tests for the family of IEC 60603-7-x connectors.
These connectors are intermateable (according to IEC 61076-1 level 2) and interoperable with
other IEC 60603-7 series connectors.

    • sale 10% off
    • Standard
      58 pages
      English language
    • e-Library read for
      1 day

This document specifies the requirements of the test procedures to be applied for recurrent tests of current-using electrical equipment and appliances for the verification of the effectiveness of the protective measures and the permissible limits for product compliance.
This procedure is applicable to current-using electrical equipment connected to final circuits. They can be either pluggable equipment type A connected to final circuits at work places via a plug or permanently connected equipme...
view more

    • sale 10% off
    • Standard
      35 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      36 pages
      English language
    • e-Library read for
      1 day

This part of IEC 61076 describes circular connectors with M8 screw locking typically used for
data and power transmissions in industrial applications. These connectors consist of fixed and
free connectors that are either rewireable or non-rewireable. Data transmission performance
is for Category 5 up to 100 MHz.
Two coded versions, identified as D-coded and P-coded, are provided that differ by their pin
size and optionally by number of poles, hence by the function provided for field applica...
view more

    • sale 10% off
    • Standard
      51 pages
      English language
    • e-Library read for
      1 day

The objective of this part of IEC 62433 is to describe the extraction flow for deriving an
immunity macro-model of an Integrated Circuit (IC) against conducted Electrostatic Discharge
(ESD) according to IEC 61000-4-2 and Electrical Fast Transients (EFT) according to
IEC 61000-4-4.
The model addresses physical damages due to overvoltage, thermal damage and other failure
modes. Functional failures can also be addressed.
This model allows the immunity simulation of the IC in an application. T...
view more

    • sale 10% off
    • Standard
      58 pages
      English language
    • e-Library read for
      1 day

This part of IEC 60747 specifies the terminology, essential ratings, characteristics, safety test
and the measuring methods of magnetic coupler and capacitive coupler.
It specifies the principles and requirements of insulation and isolation characteristics for
magnetic and capacitive couplers for basic insulation and reinforced insulation.

    • sale 10% off
    • Standard
      55 pages
      English language
    • e-Library read for
      1 day

This document provides guidance on addressing research and innovation (R&I) in European standardization activities and deliverables.
Secretaries and chairpersons of CEN/CENELEC Technical Bodies as well as CEN/CENELEC national members are encouraged to actively promote the application of this document.

    • sale 10% off
    • Guide
      16 pages
      English language
    • e-Library read for
      1 day

This European Standard establishes the requirements and tests for cover plates and cover tapes used for the mechanical protection, identification and warning of the location of buried cables or buried conduits.

    • sale 10% off
    • Standard
      17 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      14 pages
      English language
    • e-Library read for
      1 day

This part of IEC 60749 provides a means of assessing the resistance to soldering heat of
semiconductors packaged as plastic encapsulated surface mount devices (SMDs). This test is
destructive.

    • sale 10% off
    • Standard
      30 pages
      English language
    • e-Library read for
      1 day

This CEN-CENELEC Guide provides mechanisms and details the characteristics and development process of the CEN/CENELEC deliverable known as the 'CEN/CENELEC Workshop Agreement'.

    • sale 10% off
    • Guide
      24 pages
      English language
    • e-Library read for
      1 day

This part of IEC 60749 establishes a standard procedure for determining the preconditioning
of non-hermetic surface mount devices (SMDs) prior to reliability testing.
The test method defines the preconditioning flow for non-hermetic solid-state SMDs
representative of a typical industry multiple solder reflow operation.
These SMDs are subjected to the appropriate preconditioning sequence described in this
document prior to being submitted to specific in-house reliability testing (qualificati...
view more

    • sale 10% off
    • Standard
      15 pages
      English language
    • e-Library read for
      1 day

This part of IEC 63041 is applicable to piezoelectric physical sensors mainly used in the field
of process control, wireless monitoring, dynamics, thermodynamics, vacuum engineering, and
environmental sciences. This document provides users with technical guidelines as well as
basic knowledge of common physical sensors.
Piezoelectric sensors covered herein are those applied to the detection and measurement of
physical quantities such as force, pressure, torque, viscosity, temperature, film t...
view more

    • sale 10% off
    • Standard
      16 pages
      English language
    • e-Library read for
      1 day

This part of IEC 60749 describes a test used to determine whether encapsulated solid state
devices used for through-hole mounting can withstand the effects of the temperature to which
they are subjected during soldering of their leads by using wave soldering.
In order to establish a standard test procedure for the most reproducible methods, the solder
dip method is used because of its more controllable conditions. This procedure determines
whether devices are capable of withstanding the sol...
view more

    • sale 10% off
    • Standard
      12 pages
      English language
    • e-Library read for
      1 day

The contents of the corrigendum of September 2020 have been included in this copy.

    • sale 10% off
    • Amendment
      9 pages
      English language
    • e-Library read for
      1 day

This part of IEC 62966, dedicated to aisle containment techniques for information technology
(IT) equipment typically used in data centres, describes the quantification of its air tightness, in
particular the air loss ratio that describes the content of the volumetric flow not used for cooling
the IT equipment. This ratio provides an index of efficiency, being inversely proportional to
efficiency (the lower this ratio, the higher the efficiency). This document provides methods to
measure an...
view more

    • sale 10% off
    • Standard
      27 pages
      English language
    • e-Library read for
      1 day

This part of IEC 61076 specifies circular connectors with an inner push‑pull locking
mechanism of a size derived from and thus being compatible with M12 screw‑locking
connectors and with mating interfaces according to IEC 61076‑2‑101, IEC 61076‑2‑109,
IEC 61076‑2‑111 and IEC 61076‑2‑113.
A female fixed connector with inner push-pull locking according to this document is
intermateable with a correspondingly coded male free connector with M12 screw-locking
according to IEC 61076-2-101, IEC 6...
view more

    • sale 10% off
    • Standard
      65 pages
      English language
    • e-Library read for
      1 day

This part of IEC 60352 is applicable to solderless press-in connections for use in electrical
and electronic equipment and components.
The press-in connection consists of a termination having a suitable press-in zone which is
inserted into a hole of a board.
Information on materials and data from industrial experience is included in addition to the test
procedures to provide electrically stable connections under specified environmental conditions.
The object of this document is to determin...
view more

    • sale 10% off
    • Standard
      38 pages
      English language
    • e-Library read for
      1 day

This part of IEC 60747 specifies the terminology, essential ratings, characteristics, safety
tests, as well as the measuring methods for photocouplers.
NOTE The term "optocoupler" can also be used instead of "photocoupler".

    • sale 10% off
    • Standard
      56 pages
      English language
    • e-Library read for
      1 day

This part of the IEC 62435 series on long-term storage is applied to passive electronic devices
in long-term storage that can be used as part of obsolescence mitigation strategy. Longterm
storage refers to a duration that can be more than 12 months for product scheduled for
storage. Storage typically begins when components are packed at the originating supplier
where the pack date or date code are assigned to the product. It is the responsibility of the
distributor and the customer to contr...
view more

    • sale 10% off
    • Standard
      20 pages
      English language
    • e-Library read for
      1 day

This document specifies standard aspect ratios for logarithmic or level characteristics
expressed in decibels versus a logarithmic frequency axis and ranges for the radius of polar
diagrams of level. Applications include hard copy printouts, electronic files (e.g., PDF files),
scientific publications, screen displays in computer programs and apps, as well as graphs in
standards.
Informative examples of graphs that conform to the requirements in this document are found in
Annex A.
Although...
view more

    • sale 10% off
    • Standard
      16 pages
      English language
    • e-Library read for
      1 day

This part of IEC 60749 specifies the procedural requirements for performing valid endurance,
retention and cross-temperature tests based on a qualification specification. Endurance and
retention qualification specifications (for cycle counts, durations, temperatures, and sample
sizes) are specified in JESD47 or are developed using knowledge-based methods such as in
JESD94.

    • sale 10% off
    • Standard
      23 pages
      English language
    • e-Library read for
      1 day

This part of IEC 60512, when required by the detail product specification, is used for testing
connectors or solderless connections within the scope of technical committee 48. It may also be
used for similar devices when specified in a detail product specification.
The object of this document is to detail a standard method for subjecting solderless
connections to thermal stress conditioning by cyclic current loading.

    • sale 10% off
    • Standard
      14 pages
      English language
    • e-Library read for
      1 day

This document is applicable to
– therapy equipment using extracorporeally induced non-focused or weakly focused pressure
pulses;
– therapy equipment producing extracorporeally induced non-focused or weakly focused
mechanical energy,
where the pressure pulses are released as single events of duration up to 25 μs.
This document does not apply to
– therapy equipment using focusing pressure pulse sources such as extracorporeal
lithotripsy equipment;
– therapy equipment using other acoustic ...
view more

    • sale 10% off
    • Standard
      64 pages
      English language
    • e-Library read for
      1 day

IEC 60352-4:2020 is applicable to non-accessible ID connections for which the tests and measurements according to Clauses 6 through 8 are suitable and which are made with: – appropriately designed ID terminations; – wires having solid round conductors of 0,25 mm to 3,6 mm nominal diameter; – wires having stranded conductors of 0,05 mm2 to 10 mm2 cross-sectional area; for use in electrical and electronic equipment and components. Information on materials and data from industrial experience is inc...view more

    • sale 10% off
    • Standard
      47 pages
      English language
    • e-Library read for
      1 day

This part of IEC 61969 specifies a set of basic environmental requirements and tests, as well
as safety aspects for outdoor enclosures under conditions of non-weather protected locations
above ground.
The purpose of this document is to define a minimum level of environmental performance in
order to meet requirements of storage, transport and final installation. The intention is to
establish basic environmental performance criteria for outdoor enclosure compliance.

    • sale 10% off
    • Standard
      16 pages
      English language
    • e-Library read for
      1 day

This European Standard (EN) will provide a general methodology for the assessment of the ability to re-manufacture energy related products.
This EN will elaborate the assessment and process of re-manufacturability in a horizontal, cross-product way. However, a correct assessment can only be done in a product-specific way, taking into account specific parameters of a specific energy related product.

    • sale 10% off
    • Standard
      14 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      17 pages
      English language
    • e-Library read for
      1 day

This part of IEC 61969 contains design guidelines for outdoor enclosures and is applicable over
a wide field of mechanical, electromechanical and electronic equipment and its installation
where a modular design is used.
The objectives of this document are:
– to provide an overview of specifications for enclosures focused on requirements for outdoor
applications for stationary use at non-weather protected locations, and
– to achieve product integrity under outdoor conditions and to ease pro...
view more

    • sale 10% off
    • Standard
      17 pages
      English language
    • e-Library read for
      1 day

This part of IEC 60565 specifies methods and procedures for free-field calibration of
hydrophones, as well as individual electroacoustic transducers that can be used as
hydrophones (receivers) and/or projectors (source transducers). Two general types of
calibration are covered within this document: absolute calibration using the method of threetransducer
spherical-wave reciprocity, and relative calibration by comparison with a reference
device which has already been the subject of an absolu...
view more

    • sale 10% off
    • Standard
      92 pages
      English language
    • e-Library read for
      1 day

This document defines the measurement method for the determination of the durability of
radio frequency (RF) surface acoustic wave (SAW) and bulk acoustic wave (BAW) devices,
such as filters and duplexers, with respect to high power RF signals, which are used in
telecommunications, measuring equipment, radar systems and consumer products. RF BAW
devices include two types: those based on the film bulk acoustic resonator (FBAR) technology
and those based on the solidly mounted resonator (SMR)...
view more

    • sale 10% off
    • Standard
      23 pages
      English language
    • e-Library read for
      1 day

This Guide sets out the rules for the drafting and presentation of candidate harmonized European Standards (hENs) for construction products drafted in the framework of Regulation (EU) 305/2011 (Construction Products Regulation).
This Guide gives rules which are additional to the CEN-CENELEC Internal Regulations - Part 3 (based on ISO/IEC Directives, Part 2) when this is necessary because of the special provisions of harmonized product standards in the construction sector.
This Guide applies to...
view more

    • sale 10% off
    • Guide
      14 pages
      English language
    • e-Library read for
      1 day

This part of IEC 61076 describes 2-pole or 3-pole power plus 2-pole signal shielded and
sealed connectors with plastic housing (hereinafter referred to as a connector) for electrical
and electronic equipment, including overall dimensions, interface dimensions, technical
characteristics, performance requirements and test methods.
This document is applicable to electrical connectors with sealing and shielding requirements
meeting this document, with a rated voltage up to and including 750 V a...
view more

    • sale 10% off
    • Standard
      45 pages
      English language
    • e-Library read for
      1 day

This part of IEC 63171 covers two-way, shielded or unshielded, free and fixed connectors for
data transmission with frequencies up to 600 MHz and with current carrying capacity up
to 2,0 A at 60 °C. It is intended to specify the common dimensions, mechanical, electrical,
signal integrity, environmental characteristics, reliability specifications and corresponding
tests for these connectors.

    • sale 10% off
    • Standard
      35 pages
      English language
    • e-Library read for
      1 day

This part of IEC 62933 primarily describes safety aspects for people and, where appropriate,
safety matters related to the surroundings and living beings for grid-connected energy storage
systems where an electrochemical storage subsystem is used.
This safety standard is applicable to the entire life cycle of BESS (from design to end of service
life management).
This document provides further safety provisions that arise due to the use of an electrochemical
storage subsystem (e.g. battery ...
view more

    • sale 10% off
    • Standard
      78 pages
      English language
    • e-Library read for
      1 day

This part of IEC 60352 is applicable to ID connections which are accessible for tests and
measurements according to Clauses 6 through 8 and which are made with:
– appropriately designed accessible ID terminations,
– wires having solid round conductors of 0,25 mm to 3,6 mm nominal diameter,
– wires having stranded conductors of 0,05 mm2 to 10 mm2 cross-sectional area,
for use in electrical and electronic equipment and components.
Information on materials and data from industrial experience ...
view more

    • sale 10% off
    • Standard
      44 pages
      English language
    • e-Library read for
      1 day

This part of IEC 61076 describes 2-pole or 3-pole power plus 2-pole signal shielded and
sealed connectors with plastic housing (hereinafter referred to as a connector) for electrical
and electronic equipment, including overall dimensions, interface dimensions, technical
characteristics, performance requirements and test methods.
This document is applicable to electrical connectors with sealing and shielding requirements
meeting this document, with a rated voltage up to and including 750 V a...
view more

    • sale 10% off
    • Standard
      45 pages
      English language
    • e-Library read for
      1 day

This part of IEC 61076 describes 2-pole or 3-pole power plus 2-pole signal shielded and
sealed connectors with plastic housing (hereinafter referred to as a connector) for electrical
and electronic equipment, including overall dimensions, interface dimensions, technical
characteristics, performance requirements and test methods.
This document is applicable to electrical connectors with sealing and shielding requirements
meeting this document, with a rated voltage up to and including 750 V a...
view more

    • sale 10% off
    • Standard
      44 pages
      English language
    • e-Library read for
      1 day

IEC 63171-6:2020, covers 2-way and 4-way (data/power) shielded free and fixed connectors for data transmission with frequencies up to 600 MHz and specifies the common dimensions, mechanical, electrical and transmission characteristics and environmental requirements as well as test specifications respectively. This document specifies several properties overlapping with specifications in the IEC 63171 series which have been drafted later. In case of conflict the specifications within this document...view more

    • sale 10% off
    • Standard
      54 pages
      English language
    • e-Library read for
      1 day

IEC 62610-6 which deals with thermal management for cabinets in accordance withIEC 60297 and IEC 60917 series, provides compatible measurement methods of recirculationratio and bypass ratio which are indicators for defining quality of airflow in the forced air coolingthat can be commonly applied to indoor cabinets for mounting subrack and/or chassis-basedequipment.

    • sale 10% off
    • Standard
      27 pages
      English language
    • e-Library read for
      1 day